|
|
|
|
|
|
Floor Pan Bolt (Pan to Body, Chassis to Mounting Bolt), 8 x 1.25mm
|
Price: $0.95
SALE ITEM! use code TOOMANY30
|
|
|
Floor Pan Bolt (Pan to Body, Chassis to Mounting Bolt), 8 x 1.25mm is the pointy bolt that you can drive through rust and the floor pan gasket, to bolt your VW Body down tight to the floor pan or chassis. This does not include the washer.
|
|
|
|
|
|
|
|
|
|
Floor Pan Washer (Pan to Body, Chassis to Mounting Washer), 311-899-131
|
Price: $1.95
SALE ITEM! use code TOOMANY30
|
|
|
Floor Pan Washer (Pan to Body, Chassis to Mounting Washer), 311-899-131 is the washer the pointy pan bolt goes through, to bolt your VW Body down tight to the floor pan or chassis. This does not include the bolt. The Beetle needs 18 washers to do one full chassis, the Ghia needs 24.
|
|
|
|
|
|
|
|
|
|
"Large" (50mm long) Floor Pan BOLT (Pan to Body, Chassis to Mounting Bolt), 10 x 1.5 threads, EACH, 111-899-147
|
Price: $1.95
SALE ITEM! use code TOOMANY30
|
|
|
"Large" Floor Pan BOLT (Pan to Body, Chassis to Mounting Bolt), 10 x 1.5 x 50mm, EACH, 111-899-147 is the larger floor pan bolt near the front of the pan. Most kits don't include these, and they can be tough to find!
|
|
|
|
|
|
|
|
|
|
Bumper Bracket Spacer, 1950-67 Type 1, Front or Rear, 111-707-121HD
|
|
|
Bumper Bracket Spacer, Front or Rear, 1950-67 Type 1, 111-707-121HD is the bumper bracket spacers that fits between the bumper bracket to the bumper. Gives your deck lid room to open without hitting your bumper. These are sold per EACH.
|
|
|
|
|
|
|
|
|
|
Shock Pad, Body to Axle Beam, Front, All Standard Beetle, Karmann Ghia, and Thing, PAIR, 111-899-123A-111-123A
|
|
|
Shock Pad, Body to Axle Beam, Front, All Standard Beetle, Karmann Ghia, and Thing, PAIR, 111-899-123A-111-123A sit on top of the axle beam to prevent body flex and vibration. The pan bolts pass thru the washers then these pads, holding the body tight!
|
|
|
|
|
|
|
|
|
|
Shock Pad, Body to Chassis, Rear, 10mm Thick, 1956-77 Beetle, Super Beetle, Ghia, and THING, 2 Pieces, 111-899-117B-113-115A
|
Price: $5.95
SALE ITEM! use code TOOMANY30
|
|
|
Shock Pad, Body to Chassis, Rear, 10mm Thick, 1956-77 Beetle, Super Beetle, Ghia, and THING, 2 Pieces, 111-899-117B-113-115A sit between the pan and body, and dampen road vibration. Typically there are 2 thicknesses used, 10mm and 17mm, these are the 10mm. Ideally you'd buy 2 sets of the 10mm thick, and 1 set of the thicker ones. Put the thin ones on all 4s, and IF there is a gap at one of the locations (typically the rear one in the rear wheel well), swap them out for the thicker ones, then bolt it down.
Warning: it's very common for the bolt that holds the body to the chassis to be very seized, be sure to use a lot of penetrating oil and work it back and forth to loosen it, shearing it off is a pain to deal with!
Also, if you have a 1968 and later car with a "clunk" in the back that you can't figure out (you'd changed shocks with no luck), usually the rear pads are compressed, and the body has a gap to the chassis. The body is flexing when you hit a bump, and hitting the pad. Using the thick pad and tightening the bolt down to prevent the flex will solve the problem!
|
|
|
|
|
|
|
|
|
|
Shock Pad, Body to Chassis, Rear, 17mm Thick, 1956-77 Beetle, Super Beetle, Ghia, and THING, 2 Pieces, 111-899-115A-113-115
|
|
|
Shock Pad, Body to Chassis, Rear, 17mm Thick, 1956-77 Beetle, Super Beetle, Ghia, and THING, 2 Pieces, 111-899-115A-113-115 sit between the pan and body, and dampen road vibration. Typically there are 2 thicknesses used, 10mm and 17mm, these are the 17mm. Ideally you'd buy 2 sets of the 10mm thick, and 1 set of the thicker ones. Put the thin ones on all 4s, and IF there is a gap at one of the locations (typically the rear one in the rear wheel well), swap them out for the thicker ones, then bolt it down. Warning: it's very common for the bolt that holds the body to the chassis to be very seized, be sure to use a lot of penetrating oil and work it back and forth to loosen it, shearing it off is a pain to deal with! Also, if you have a 1968 and later car with a "clunk" in the back that you can't figure out (you'd changed shocks with no luck), usually the rear pads are compressed, and the body has a gap to the chassis. The body is flexing when you hit a bump, and hitting the pad. Using the thick pad and tightening the bolt down to prevent the flex will solve the problem!
|
|
|
|
|
|
|
|
|
|
Karmann Ghia License Plate, GERMAN Oval w/Ghia Logo, EACH, 141-006-100KG
|
|
|
Karmann Ghia License Plate, German Oval w/Ghia Logo, EACH, 141-006-100KG is a nice item to customize your show car, or to put on the front (if your state allows it) to declare your car! Holes are in the stock license plate location for easy mounting.
|
|
|
|
|
|
|
|
|
|
Bumper Bracket Grommet, 1968-73 Type 1, Set of 4, 111-707-197B-111-197
|
Price: $7.95
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
Bumper Bracket Grommet, 1968-73 Type 1, Set of 4, 111-707-197B-111-197 are the rubber grommets which keeps mud and rocks from the fenderwell from making it's way through the body holes and spoiling your nice looking paint job! They also prevent rust from forming along seams.
|
|
|
|
|
|
|
|
|
|
Battery Hold Down Clamp, 1967 and Later Beetle and Super Beetle, 1968-71 Ghia, 1968-71 Type 2, 1967 and Later Type 3, 131-915-313
|
Price: $7.95
SALE ITEM! use code TOOMANY30
|
|
|
Battery Hold Down Clamp, 1967 and Later Beetle and Super Beetle, 1968-71 Ghia, 1968-71 Type 2, 1967 and Later Type 3, 131-915-313 hold the battery down tight, so it doesn't flop and bounce around, which can cause major clunking and even a fire if the battery grounds out!
|
|
|
|
|
|
|
|
|
|
License Plate Bracket, 1968-79 Type 1 Front and Rear, AND 1950-79 Type 2, 113-943-901-113-905
|
Price: $8.95
SALE ITEM! use code TOOMANY30
|
|
|
License Plate Bracket, 1968-79 Type 1 Front and Rear, AND 1950-79 Type 2, 113-943-901-113-905 often gets mangled or lost during paint jobs and license plate transfers. These are inexpensive and give a good finished look, instead of all raggedy with bent/painted brackets!
|
|
|
|
|
|
|
|
|
|
Front License Plate Mounting Kit, 1954-67 Beetle and 1956-71 Karmann Ghia, 113-707-901B
|
|
|
Front License Plate Mounting Kit, 1954-67 Beetle and 1956-71 Karmann Ghia, 113-707-901B is the kit with the small P-clamps which hangs your license plate from the upper tube on your front bumper! You need 1 of these per car to do the front.
|
|
|
|
|
|
|
|
|
|
|
Deck Lid Hardware Kit, 1968 and Newer VW Beetle and Karmann Ghia, Stainless Steel
|
|
|
Deck Lid Hardware Kit, 1968 and Newer VW Beetle and Karmann Ghia, Stainless Steel includes the stainless stuff you need to bolt the deck lid to the car, and also includes the latch and light housing hardware too!
|
|
|
|
|
|
|
|
|
|
|
Deck Lid Hardware Kit, 1966 and Older VW Beetle and Karmann Ghia, Stainless Steel
|
|
|
Deck Lid Hardware Kit, 1966 and Older VW Beetle and Karmann Ghia, Stainless Steel includes the stainless stuff you need to bolt the deck lid to the car, and also includes the latch and light housing hardware too!
|
|
|
|
|
|
|
|
|
|
Karmann Ghia Rear Hood Rain Tray Rivet and Screw Kit, 1970-74 Karmann Ghia, 9pc Kit, 141-827-081ST
|
|
|
Karmann Ghia Rear Hood Rain Tray Rivet and Screw Kit, 1970-74 Karmann Ghia, 9pc Kit, 141-827-081ST are needed to install the actual Rain Tray. The original clips are likely missing, or ready to break if they are not broken already! Don't forget the (2)
grommets and drain hoses too, which are all seen in the Related Products section.
|
|
|
|
|
|
|
|
|
|
|
Bumper Bracket Hardware Kit, VW Beetle and Karmann Ghia to 1967, Stainless Steel
|
|
|
Bumper Bracket Hardware Kit, VW Beetle and Karmann Ghia to 1967, Stainless Steel includes the stainless bolts and washers to bolt your bumper brackets to the car body. Does all 4 bumper brackets on your Early VW Beetle or Karmann Ghia.
|
|
|
|
|
|
|
|
|
|
Karmann Ghia Rain Tray Drain Tube Grommets, PAIR, 141-827-079
|
|
|
Karmann Ghia Rain Tray Drain Tube Grommets, PAIR, 141-827-079 are needed to install the actual Rain Tray. These fit the original and our reproduction trays and tubes. Don't forget the Drain Tubes and the 9pc install kit, which are all seen in the Related Products section.
|
|
|
|
|
|
|
|
|
|
|
Stainless Bumper Bracket Hardware Kit, 1968 and Later VW Beetle and Karmann Ghia
|
|
|
Stainless Bumper Bracket Hardware Kit, for 1968 and Later VW Beetle and Karmann Ghia includes the stainless bolts and washers to bolt your bumper brackets to the car body. Does all 4 bumper brackets on your LATE VW Beetle or Karmann Ghia.
|
|
|
|
|
|
|
|
|
|
Karmann Ghia Rain Tray Drain Tube, EACH, 141-827-077
|
|
|
Karmann Ghia Rain Tray Drain Tube, EACH, 141-827-077 are needed to install the actual Rain Tray. These route the water down and away! You'll need 2 of these to equip one drain tray properly. Don't forget the (2)
grommets and 9pc install kit, which are all seen in the Related Products section.
|
|
|
|
|
|
|
|
|
|
|
Bumper Hardware Kit, VW Beetle and Karmann Ghia to 1967, Stainless Steel
|
|
|
Bumper Hardware Kit, VW Beetle and Karmann Ghia to 1967, Stainless Steel includes the stainless bolts and washers to bolt your bumper brackets to the bumper itself. Does all 4 bumper brackets on your Early VW Beetle or Karmann Ghia.
|
|
|
|
|
|
|
|
|
|
Floor Pan Gasket, Beetle, Super Beetle, Thing, and Ghia, 19' Long, 113-701-605-113-605
|
|
|
Floor Pan Gasket, Beetle, Super Beetle, Thing, and Ghia, 19' Long, 113-701-605-113-605 seals the mating surfaces/gap between the body and the floor pan. Cushion design allows it to be used in locations other than it's intended use! Water tight seal, and you can finish the seal with some UV Resistant Household silicone.
|
|
|
|
|
|
|
|
|
|
Fast Fab Dashboard Repair Section, Ghia 1956-1965
|
|
|
This Made in USA Dashboard Repair Section fits 1956-1965 VW Ghias, it's a perfect reproduction to the original! Factory Radio Block Off Panels fit perfect (as expected). This needs to be welded into place and properly finished for the best job.
|
|
|
|
|
|
|
|
|
|
Stainless Bumper Hardware Kit, 1968 and Later VW Beetle and Karmann Ghia
|
|
|
Stainless Bumper Hardware Kit, 1968 and Later VW Beetle and Karmann Ghia includes the stainless bolts and washers to bolt your bumper brackets to the bumper itself. Does all 4 bumper brackets on your LATE VW Beetle or Karmann Ghia.
|
|
|
|
|
|
|
|
|
|
Chrome Steel T-bars, 1968-73 Beetle and Ghia, PAIR
|
|
|
Chrome plated Steel T-bars fit 1968-1973 Beetles and ghias. One pair does a front OR back of the car, you need 2 sets to do an entire car. These will really lighten your car and clean up the looks!
|
|
|
|
|
|
|
|
|
|
Headlight Bucket Assembly (NO BULB), 1967+ Type 1, 1968-79 Type 2, and 1961-74 Type 3, 141-941-041EC
|
|
|
Headlight Bucket Assembly (NO BULB), 1967+ Type 1, 1968-79 Type 2, and 1961-74 Type 3, 141-941-041EC is the assembly that bolts the headlight to the car's fender. It allows headlight aim adjustments. These get bent and mangled in accidents.
|
|
|
|
|
|
|
|
|
|
Chrome Steel T-bars, 1956-67 Beetle and Ghia, PAIR
|
|
|
Chrome plated Steel T-bars fit early beetles and ghias. One pair does a front OR back of the car, you need 2 sets to do an entire car. These will really lighten your car and clean up the looks!
|
|
|
|
|
|
|
|
|
|
HELLA (Mex) Headlamp with H4 Bulb, 1967+ Type 1, 1968-79 Type 2, and 1961-74 Type 3, BAA941751A
|
|
|
HELLA (Mex) Headlamp with H4 Bulb, 1967+ Type 1, 1968-79 Type 2, and 1961-74 Type 3, BAA941751A is Genuine Hella of Mexico AND COMES WITH A HELLA H4 HALOGEN SEALED BEAM! This is the headlamp and bulb. Housing is sold separately.
|
|
|
|
|
|
|
|
|
|
Karmann Ghia Rear Hood Rain Tray, 1970-74 Karmann Ghia, 141-827-071
|
|
|
Karmann Ghia Rear Hood Rain Tray, 1970-74 Karmann Ghia, 141-827-071 is an incredibly functional part which prevents water from
getting into the engine compartment (and in your carburetors!) through
the deck lid vents on the top of the deck lid. This part requires (2)
grommets, the drain hoses, and the mounting clips and screws, which are all seen in the Related Products section.
|
|
|
|
|
|
|
|
|
|
Headlight Bucket (WELD-IN), 1956-74 Karmann Ghia, EACH, 141-809-145C
|
Price: $74.95
SALE ITEM! use code TOOMANY30
|
|
|
Headlight Bucket (WELD-IN), 1956-74 Karmann Ghia, EACH, 141-809-145C often rusts out from water and salt splashed onto it from the front wheel. These restore your car's headlight area back to water-tight status!
|
|
|
|
|
|
|
|
|
|
Aluminum T-Bar Set, 1967 & Earlier, Beetle and Ghia, Set of 4
|
|
|
Original Cal-Look T-bars are back in Aluminum! These fit early 1956-67 Beetles and Ghias with a classic Cal-Look appearance! One set of these does all 4 corners of your car! These will really lighten your car and clean up the "look" -- They are NOT show quality finish though, so will need some polishing work.
|
|
|
|
|
|
|
|
|
|
Aluminum T-Bar Set, 1968-73 Beetle and Ghia, Set of 4
|
|
|
Original Cal-Look T-bars are back in polished Aluminum! These fit "Late" 1968-73 Beetles and Ghias. One set does all 4 corners of your car in classic Cal-Look Style!. These will really lighten your car and clean up the looks!
|
|
|
|
|
|
|
|
|
|
Rattle Trap Extreme Super Stick Sound Deadener, 80 mil Nominal Thickness, 50sq' (33.5' x 18" Roll)
|
|
|
Want to make your VW Quieter? Rattle Trap Extreme Super Stick Sound Deadener, 80 mil Nominal Thickness, 50sq' (33.5' x 18" Roll) is the finest sound deadener we have found! We tried them all, and they were either too expensive, smelled like you just paved the inside of your car, or didn't stick! Until we came across Fat Mat and Rattle Trap! These 2 products are from the same company, but in 40 mil and 80 mil thicknesses respectively. Rattle Trap is 1/3 less than Dynamat, and we feel it works better to boot!
|
|
|
|
|
|
|
|
|
|
|
Floor Pan Half, Left, 1956-74 VW Karman Ghia Coupe and Convertible, 141-701-059A
|
|
|
Floor Pan Half, Left, 1956-74 VW Karmann Ghia Coupe and Convertible, 141-701-059A does NOT include the seat tracks. These are not as nice as original German Pans, but these are the nicest we have been able to acquire! Don't forget the pan gaskets too!
These ship ONLY within the Continental USA via GREYHOUND FREIGHT to your nearest Greyhound Freight "GPX"Depot (not to your door!) This item cannot ship internationally.
|
|
|
|
|
|
|
|
|
|
|
Floor Pan Half, Right, 1956-74 VW Karman Ghia Coupe and Convertible, 141-701-060A
|
|
|
Floor Pan Half, Right, 1956-74 VW Karman Ghia Coupe and Convertible, 141-701-060A does NOT include the seat tracks. These are not as nice as original German Pans, but these are the nicest we have been able to acquire! Don't forget the pan gasket too!
These ship ONLY within the Continental USA via GREYHOUND FREIGHT to your nearest Greyhound Freight "GPX"Depot (not to your door!) This item cannot ship internationally.
|
|
|
|
