|
|
|
|
|
Gaugebox/Switchbox, 9.75 X 6.5 X 4", Brushed Aluminum, Undrilled
|
|
These Aluminum Switchboxes provide a custom way to install gauges and/or switches into your car or buggy. Brushed aluminum finish LOOKS GREAT. This one has a face that is undrilled for a custom setup the way YOU want it!
|
|
|
|
|
|
|
|
Gaugebox/Switchbox, 4.50 X 6.50 X 4", Brushed Aluminum
|
|
These Aluminum Switchboxes provide a custom way to install gauges and/or switches into your car or buggy. Brushed aluminum finish LOOKS GREAT. This has (2) 3/4" Holes, and (4) 1/2" Holes for switches and warnign lights (No Gauges).
|
|
|
|
|
|
|
|
Rubber Boot for Sealed Switch
|
|
Rubber Boot for Sealed Switch fits 3570, 3571, 3572, and 3573.
|
|
|
|
|
|
|
|
Switch Guard for Sealed Switch
|
|
Switch Guard for Sealed Switch fits 3570, 3571, 3572, and 3573.
|
|
|
|
|
|
|
|
HD Sealed Switch, Off-On-On, 20 Amp
|
|
Sealed toggle switches feature dust and water resistant construction. These feature push on terminals, and a rubber toggle cover to keep $)#*&) out! 20A capable for most any application. Switch body is sealed for LIFE against moisture and dirt.
|
|
|
|
|
|
|
|
HD Sealed Switch, Off-On-Momentary On, 20 Amp
|
|
Sealed toggle switches feature dust and water resistant construction. These feature push on terminals, and a rubber toggle cover to keep $)#*&) out! 20A capable for most any application. Switch body is sealed for LIFE against moisture and dirt.
|
|
|
|
|
|
|
|
HD Sealed Switch, On-Off-On, 20 Amp
|
|
Sealed toggle switches feature dust and water resistant construction. These feature push on terminals, and a rubber toggle cover to keep $)#*&) out! 20A capable for most any application. Switch body is sealed for LIFE against moisture and dirt.
|
|
|
|
|
|
|
|
Mega Mount Billet Aluminum Tach Bracket
|
|
This billet clamp tachometer bracket provide the equipment for an easy installation, and one that looks great too! It also has a machined hole to run the wires in so they are virtually invisible!
|
|
|
|
|
|
|
|
Mega Mount Billet Aluminum 1 1/2" Tubing Adapter Clamp
|
|
This adapter allows you to bolt up our Mega Mount Tachometer bracket to a 1 1/2" diameter chassis or frame tubing.
|
|
|
|
|
|
|
|
VDO Direct Mount Gauge, 15psi, 1 1/2" White Face, 1/8-27 NPT
|
|
VDO's direct mount low pressure gauge is nice for monitoring fuel pressure. Excessive fuel pressure causes fuel control problems, and insufficient pressure will create fuel starvation under driving conditions!
|
|
|
|
|
|
|
|
Mechanical Gauge Tubing Kit, 16'
|
|
VDO Tubing Kit is used with VDO's Turbo BOOST gauge, and VDO's Mechanical Oil Pressure Gauge. This kit makes the connection of your gauge to your engine a snap! 16' of tubing is supplied so you can do the installation on most any car.
|
|
|
|
|
|
|
|
VDO 100psi Mechanical Oil Pressure Gauge, Cockpit, 2 1/16", Black Face, V150030
|
|
VDO 100psi Mechanical Oil Pressure Gauge, Cockpit, 2 1/16", Black Face, V150030 monitors oil pressure of your engine without the use of finicky electrical sending units. Mechanical gauges are more reliable than electrical ones, and don't need an electrical system to operate! This gauge does NOT come with the tubing kit, which must be purchased separately.
|
|
|
|
|
|
|
|
VDO Ammeter, 60 Amp, Cockpit, 2 1/16", Black Face, V190031
|
|
VDO Ammeter, 60 Amp, Cockpit, 2 1/16", Black Face, V190031 installs between the battery and your car's electrical system, to see if you are pulling more current out of the battery than the alternator or generator can supply. Extended discharge will empty your battery of juice!
|
|
|
|
|
|
|
|
VDO Ammeter, 30 Amp, Cockpit, 2 1/16", Black Face
|
|
This 30A VDO Ammeter Gauge installs between the battery and your car's electrical system, to see if you are pulling more current out of the battery than the alternator or generator can supply. Extended discharge will empty your battery of juice!
|
|
|
|
|
|
|
|
VDO Fuel Gauge, Cockpit, Black Face, 2 1/16" (For V221012 or OEM Sender)
|
|
VDO Fuel Gauge, Cockpit, Black Face, 2 1/16" is compatible with VDO Sending Unit # V221012.
|
|
|
|
|
|
|
|
VDO Fuel Tank Sender for 2 1/16" Fuel Gauge, Compatible with V301020 and Stock Fuel Gauge
|
|
VDO Sending Unit for VDO Fuel Gauges, this fits Standard Beetles and Ghias, DOES NOT FIT SUPERBEETLES! This bolts right in to replace the stock electrical sending unit. This sender is also compatible with the stock gauge!
|
|
|
|
|
|
|
|
VDO Universal Fuel Tank Sender for V301733 and V301015 Fuel Gauges, V226001
|
|
VDO Universal Fuel Tank Sender for V301733 and V301015 Fuel Gauges, V226001 fits Standard Beetles and Ghias, DOES NOT FIT SUPERBEETLES! This bolts right in to replace the stock electrical sending unit. This is compatible with the V301733 and V301015 Fuel Gauges.
|
|
|
|
|
|
|
|
VDO Fuel Tank Sending Unit Mount Kit, Bolt In
|
|
VDO's Bolt-In Fuel Tank Sending Unit Mount Kit allows you to install a VDO Sending unit into a fuel tank that previously did not have a sending unit at all! Comes with Flange, Gasket, and Mounting Hardware.
|
|
|
|
|
|
|
|
VDO Dimmer Ring, 2 1/16" Gauge, PAIR
|
|
This is a matte black "Hood" that fits over the gauge face, to shield the gauge from sunlight, so it's easier to see the gauge face in bright sunlight.
|
|
|
|
|
|
|
|
VDO 3-Prong Push On Connector
|
|
This is the connector that makes connecting your VDO Oil Pressure or Oil Temperature gauges up easier. You do not "need" this, but if you ever removed the wires, it can be confusing when putting them back on. This makes it so they only go on one way!
|
|
|
|
|
|
|
|
VDO Cylinder Head Temperature Wiring Kit, 15' Long, V240701
|
|
VDO Cylinder Head Temperature Wiring Kit, 15' Long, V240701 is a 15' long harness and ends to connect your VDO CHT (Cylinder Head Temperature) gauge to your thermocouple on the engine. You cannot just use regular automotive wiring for this job, due to the characteristics of the CHT Thermocouple.***THIS ITEM IS NO LONGER AVAILABLE FROM VDO!!! They now INCLUDE the harness with the CHT Senders (Thermocouples) as a package, instead of selling them separately. So if you want a harness, order the sender!
|
|
|
|
|
|
|
|
Gauge Mounting Bracket for 2 1/16" Gauge, 1 Hole
|
|
This is a Gauge Mounting Bracket/Panel for a 2 1/16" VDO Gauge. It's a steel bracket that can be gently bent to provide the best angle for gauge visibility and appearance. This mounts 1 Gauge.
|
|
|
|
|
|
|
|
Gauge Mounting Bracket for 2 1/16" Gauge, 2 Hole
|
|
This is a 2-hole Gauge Mounting Bracket/Panel for 2 1/16" size gauges. It's a steel bracket that can be gently bent to provide the best angle for gauge visibility and appearance.
|
|
|
|
|
|
|
|
Gauge Mounting Bracket for 2 1/16" VDO Gauges, 3 Hole
|
|
This is a 3 Hole Gauge Mounting Bracket/Panel for 2 1/16" VDO Gauges. It's a steel bracket that can be gently bent to provide the best angle for gauge visibility and appearance. This mounts 3 Gauges.
|
|
|
|
|
|
|
|
VDO 2 1/16" Gauge Mounting Cup, Long Length
|
|
This 2 1/16" Gauge Mounting Cup provide a method of mounting y our VDO Gauges. They are ABS, finished in Matte Black, with a steel black mounting ring. These allow you to mount your gauges, while also protecting and beautifying your gnarly wiring!
|
|
|
|
|
|
|
|
"T" Adapter for VDO Sending Unit, 1/8 - 27, per EACH, V240850
|
|
"T" Adapter for VDO Sending Unit, 1/8 - 27, V240850 is used when you want to use 2 sending units in the same place. Typically this is when you want to use a 1-Pole VDO Oil Pressure Gauge along WITH the stock idiot light sending unit, since the VDO 2-pole senders have idiot light pressure too high. The VDO idiot light sender goes on at 8-10psi, the stock VW sender is set to trigger at 2.5-3psi. Low pressure like this is NORMAL for the VW at hot idle.
|
|
|
|
|
|
|
|
VDO Blind Cover (Blank Hole Cover), 2 1/16" Gauges, EACH, V240864
|
|
VDO Blind Cover (Blank Hole Cover), 2 1/16" Gauges, Each, V240864 is a snap-in ABS covers for gauge panels that do not have a gauge in them. They are matte black with a raised bezel profile, just like a gauge face.
|
|
|
|
|
|
|
|
VDO Fuel Gauge, Cockpit, Black Face, 2 1/16", V301015
|
|
V301015 VDO Fuel Gauge, Cockpit, Black Face, 2 1/16" is compatible with VDO Sending Unit # V226001.
|
|
|
|
|
|
|
|
VDO Fuel Gauge, Cockpit, White Face, 2 1/16", V301216
|
|
V301216 VDO Fuel Gauge, Cockpit, White Face, 2 1/16" is compatible with VDO Sending Unit # V226001.
|
|
|
|
|
|
|
|
VDO 300F Oil Temp Sending Unit, 14 X 1.5mm
|
|
This VDO 300F Oil Temperature Sending Unit fits the Type 1 oil drain bolt. This is also the correct size for the T-4 engine taco plate that used the stock sender.
|
|
|
|
|
|
|
|
VDO 300F Oil Temp Sending Unit, 1/8 X 27 NPT
|
|
This VDO 300F Oil Temperature Sending Unit fits the stock Type 1 and Type 4 Oil Pressure Switch Location. This is a great thread size to tap into oil filter adapters for a high-flow (accurate) remote location for measuring your oil temperatures.
|
|
|
|
|
|
|
|
VDO 300F Oil Temp Sending Unit, 1/4 X 18 NPTF
|
|
VDO 300F Oil Temp Sending Unit, 1/4 X 18 NPTF is a great size if you happen to strip out the 1/8-27 NPT threads. Simply re-tap to 1/4 X 18 NPTF and you are set!
|
|
|
|
|
|
|
|
VDO 300F Oil Temp Sending Unit, 18 X 1.5mm
|
|
VDO 300F Oil Temp Sending Unit, 18 X 1.5mm fits they type 1 oil cooler relief plug, which is an excellent location for mounting the VDO Oil Temperature Sending Unit in VW Bugs, Ghias, and Busses.
|
|
|
|
|
|
|
|
VDO 300F Oil Temp Gauge, Cockpit, Black Face, 2 1/16"
|
|
VDO 300F Oil Temp Gauge, Cockpit, Black Face, 2 1/16" fits all sorts of VW aircooled vehicles. It's a good idea to monitor oil temperature in our vehicles, temperatures exceeding 235F means something is wrong! We also recommend a MINIMUM temp of 180F.
|
|
|
|
|
|
|
|
VDO 250F Water Temp Gauge, Cockpit, Black Face, 2 1/16"
|
|
VDO Water Temp Gauge, Cockpit, Black Face, 2 1/16" for our Watercooled friends! The stock idiot light just doesn't cut it! Cylinder head damage (warpage) can occur if you overheat your engine!
|
|
|
|
|
|
|
|
VDO 300F Oil Temp Gauge, Royale, White Face with Chrome Bezel, 2 1/16"
|
|
VDO 300F Oil Temp Gauge, Royale, White Face with Chrome Bezel, 2 1/16" fits all sorts of VW aircooled vehicles. It's a good idea to monitor oil temperature in our vehicles, temperatures exceeding 235F means something is wrong! We also recommend a MINIMUM temp of 180F.
|
|
|
|
|
|
|
|
VDO 250F Water Temp Sending Unit, 10 x 1mm
|
|
VDO 250F Water Temp Sending Unit, 10 x 1mm for our Watercooled friends! The stock idiot light just doesn't cut it! Cylinder head damage (warpage) can occur if you overheat your engine!
|
|
|
|
|
|
|
|
VDO 250F Water Temp Sending Unit, 1/8 - 27 NPT
|
|
VDO 250F Water Temp Sending Unit, 1/8 - 27 NPT for our Watercooled friends! The stock idiot light just doesn't cut it! Cylinder head damage (warpage) can occur if you overheat your engine!
|
|
|
|
|
|
|
|
VDO 250F Water Temp Gauge, Royale, White Face with Chrome Bezel, 2 1/16"
|
|
VDO 250F Water Temp Gauge, Royale, White Face with Chrome Bezel, 2 1/16" for our Watercooled friends! The stock idiot light just doesn't cut it! Cylinder head damage (warpage) can occur if you overheat your engine!
|
|
|
|
|
|
|
|
VDO Cylinder Head Temperature (CHT) 14mm Sending Unit and Harness, V323701
|
|
VDO Cylinder Head Temperature (CHT) 14mm Sending Unit, V323701 is used to monitor the critical Cylinder Head Temperature on the Aircooled VW Engine. We feel critical temperatures are 425F when the thermocouple is mounted under a 14mm spark plug.VDO has discontinued the harness SEPARATELY, VDO now includes the harness with this CHT Senders (Thermocouples) as a package, instead of selling them separately.
|
|
|
|
|
|
|
|
VDO Cylinder Head Temperature (CHT) 12mm Sending Unit, V323705
|
|
VDO Cylinder Head Temperature (CHT) 12mm Sending Unit, V323705 is used to monitor the critical Cylinder Head Temperature on the Aircooled VW Engine. We feel critical temperatures are 425F when the thermocouple is mounted under a 12mm spark plug.
|
|
|
|
|
|
|
|
VDO Voltmeter, Cockpit, Black Face, 2 1/16"
|
|
VDO Voltmeter, Cockpit, Black Face, 2 1/16" is more useful than an Ammeter for your VW bug, bus or ghia. Turn the key on and note the voltage, it should be ~12.8V (good battery). Start up the car, your voltage SHOULD go up as the charging system works.
|
|
|
|
|
|
|
|
VDO Voltmeter, Cockpit, White Face, 2 1/16"
|
|
VDO Voltmeter, Cockpit, White Face, 2 1/16" is more useful than an Ammeter for your VW bug, bus or ghia. Turn the key on and note the voltage, it should be ~12.8V (good battery). Start up the car, your voltage SHOULD go up as the charging system works.
|
|
|
|
|
|
|
|
VDO Tachometer, Cockpit, White Face, 7000 RPM, 3 3/8"
|
|
VDO Tachometer, Cockpit, White Face, 7000 RPM, 3 3/8" is a nice medium sized tach to keep tabs on your vw bug's engine RPMs. This is a reasonable size that is smaller than the huge MONSTER TACH, but not puny like the 2 1/16".
|
|
|
|
|
|
|
|
VDO Tachometer, Royale, White Face, 7000 RPM, 3 3/8"
|
|
VDO Tachometer, Royale, White Face, 7000 RPM, 3 3/8" is a nice medium sized tach to keep tabs on your vw bug's engine RPMs. This is a reasonable size that is smaller than the huge MONSTER TACH, but not puny like the 2 1/16".
|
|
|
|
|
|
|
|
VDO 120mph Speedometer, Royale, White Face with Chrome Bezel, 3 1/8"
|
|
VDO 120mph Speedometer, Royale, White Face with Chrome Bezel, 3 1/8" matches VDO's other Royale Gauges (Cylinder Head Temperature, Tachometer, Oil Pressure, Oil Temperature, Voltmeter, Ammeter, and Fuel Level. Matching gauges for your VW Beetle/Bug, Ghia, or Bus!
|
|
|
|
|
|
|
|
VDO 120mph Speedometer, Cockpit, Black Face, 3 1/8"
|
|
VDO 120mph Speedometer, Cockpit, Black Face, 3 1/8" matches VDO's other Cockpit Gauges (Cylinder Head Temperature, Tachometer, Oil Pressure, Oil Temperature, Voltmeter, Ammeter, and Fuel Level. Matching gauges for your VW Beetle/Bug, Ghia, or Bus!
|
|
|
|
|
|
|
|
VDO 120mph Speedometer, Cockpit, Black Face, 3 3/8"
|
|
VDO 120mph Speedometer, Cockpit, Black Face, 3 3/8" matches VDO's other Cockpit Gauges (Cylinder Head Temperature, Tachometer, Oil Pressure, Oil Temperature, Voltmeter, Ammeter, and Fuel Level. Matching gauges for your VW Beetle/Bug, Ghia, or Bus!
|
|
|
|
|
|
|
|
VDO 160mph Speedometer, Cockpit, Black Face, 3 3/8"
|
|
VDO 160mph Speedometer, Cockpit, Black Face, 3 3/8" matches VDO's other Cockpit Gauges (Cylinder Head Temperature, Tachometer, Oil Pressure, Oil Temperature, Voltmeter, Ammeter, and Fuel Level. Matching gauges for your VW Beetle/Bug, Ghia, or Bus!
|
|
|
|
|
|
|
|
VDO 120mph Speedometer, Cockpit, White Face, 3 1/8"
|
|
VDO 120mph Speedometer, Cockpit, White Face, 3 1/8" matches VDO's other Cockpit Gauges (Cylinder Head Temperature, Tachometer, Oil Pressure, Oil Temperature, Voltmeter, Ammeter, and Fuel Level. Matching gauges for your VW Beetle/Bug, Ghia, or Bus!
|
|
|