|
|
|
|
|
|
Vintage Speed Stainless Steel SUPER FLOW Muffler (Up to 150hp) for VW THING (Type 181), 155-203-THING-SF
|
|
|
Vintage Speed Stainless Steel Super Flow Muffler (Up to 150hp) for VW THING (Type 181), 155-203-THING-SF is the finest exhaust available for your VW THING! This retains maximum ground clearance, even if your car is lowered or slammed to the ground! This model exits the holes in the rear bumper just like stock! This is a 1 1/2" (38mm) exhaust system, which is a HUGE upgrade from the stock 1 1/4" (32mm) system. This can be used with heater boxes OR J-pipes. This is louder than our 125hp rated system.
|
|
|
|
|
|
|
|
|
|
|
Vintage Speed Stainless Steel Sport Muffler (Up to 125hp) for VW THING (Type 181), 155-203-THING
|
|
|
Vintage Speed Stainless Steel Sport Muffler (Up to 125hp) for VW THING (Type 181), 155-203-THING is the finest exhaust available for your VW THING! This retains maximum ground clearance, even if your car is lowered or slammed to the ground! This model exits the holes in the rear bumper just like stock! This is a 1 1/2" (38mm) exhaust system, which is a HUGE upgrade from the stock 1 1/4" (32mm) system. This can be used with heater boxes OR J-pipes.
|
|
|
|
|
|
|
|
|
|
A-1 Performance Sidewinder HEADER, Fits VW THING, Heater Box Version (Flanged J-pipes or Heater Boxes required)
|
|
|
A-1 Performance Sidewinder HEADER, Fits VW THING, Heater Box Version (Flanged J-pipes or Heater Boxes required) fits your unique car! Until now exhaust choices for the VW THING have really been slim, but this product opens up a great option for a healthy engine! If you are looking at buying an A-1 product, it's obvious you value quality and want the BEST! Every A-1 exhaust product is hand made to order by a master exhaust system craftsman to the custom specs you submit for YOUR car!
The THING Version of the sidewinder puts the collector ABOVE the primaries (for optimum ground clearance), while the other sidewinder versions have the collector down low UNDER the primaries.
|
|
|
|
|
|
|
|
|
|
A-1 Performance Sidewinder HEADER, Fits VW THING, J-pipe Version (NO HEATER BOXES)
|
|
|
A-1 Performance Sidewinder Header, Fits VW THING, J-pipe Version (NO HEATER BOXES) fits your unique car! Until now exhaust choices for the VW THING have really been slim, but this product opens up a great option for a healthy engine! If you are looking at buying an A-1 product, it's obvious you value quality and want the BEST! Every A-1 exhaust product is hand made to order by a master exhaust system craftsman to the custom specs you submit for YOUR car!
The THING Version of the sidewinder puts the collector ABOVE the primaries (for optimum ground clearance), while the other sidewinder versions have the collector down low UNDER the primaries.
|
|
|
|
|
|
|
|
|
|
|
A-1 Performance Sidewinder MUFFLER, Fits THING Sidewinder Header
|
|
|
A-1 Performance Sidewinder MUFFLER, Fits THING Sidewinder Header offers a 2 1/2" Hi-Flo straight through core design for THINGS! Exhaust choices for your unique car have really been slim, but this product opens up a great option for a healthy engine! If you are looking at buying an A-1 product, it's obvious you value quality and want the BEST! Every A-1 exhaust product is hand made to order by a master exhaust system craftsman to the custom specs you submit for YOUR car!
THIS MUFFLER FITS THE NON-FLANGED NON-HEATER BOXER SIDEWINDER VERSION!
|
|
|
|
|
|
|
|
|
|
A-1 Performance Phat Boy Magnaflow MUFFLER, fits Small Flange Merged Headers (Berg, Bugpack,CB, NEW EMPI, SCAT, Al's, Kymco, S&S)
|
|
|
A-1 Performance Phat Boy Magnaflow MUFFLER, fits Small Flange Merged Headers (Berg, Bugpack,CB, NEW EMPI, SCAT, Al's, Kymco, S&S) is the finest muffler available for your VW, it's made to fit YOUR CAR (not one size fits none!). Please triple check what header you have, there are MANY different headers out there, they all vary slightly in their muffler flange orientation and location! These mufflers are designed to fit as high as possible for maximum ground clearance! These mufflers are NOT QUIET! If you want a "Quiet" muffler you need a "Turbo" muffler or Quiet Pack.
SCAT: This muffler fits the SMALL FLANGE SC112, SC158, SC134 headers
CB: This fits CB Performance's SMALL FLANGE headers.
EMPI: If you have an EMPI Merged Header, you should know that EMPI has changed their header design. The new design had the collector flange perpendicular with the ground (Straight up and down). The OLD design had the flange aiming toward the ground at a 10 degree angle. So the NEW Design fits the A-1-500M-2.5, and the OLD design fits the A-1-100M-2.5.
|
|
|
|
|
|
|
|
|
|
|
A-1 Performance Phat Boy Magnaflow MUFFLER, Fits Bugpack 1 5/8" Street Max 2009-13 and 2009-23
|
|
|
A-1 Performance Phat Boy Magnaflow Muffler, Fits Bugpack 1 5/8" Street Max 2009-13 and 2009-23, is the finest muffler available for your VW, it's made to fit YOUR CAR! Now you can have great looks to go along with the HEAT you get from that header! The finest muffler available for your VW, it's made to fit YOUR CAR (not one size fits none!). Please triple check what header you have, there are MANY different headers out there, they all vary slightly in their muffler flange orientation and location! These mufflers are designed to fit as high as possible for maximum ground clearance! These mufflers are NOT QUIET! If you want a "Quiet" muffler you need a "Turbo" muffler or Quiet Pack.
|
|
|
|
|
|
|
|
|
|
|
A-1 Performance Phat Boy Magnaflow MUFFLER, fits Small Flange Merged Headers (Old EMPI, Flat 4), With Flange Angled 10 Degrees Down
|
|
|
A-1 Performance Phat Boy Magnaflow MUFFLER, fits Small Flange Merged Headers (Old EMPI, Flat 4), With Flange Angled 10 Degrees Down. The finest muffler available for your VW, it's made to fit YOUR CAR (not one size fits none!). Please triple check what header you have, there are MANY different headers out there, they all vary slightly in their muffler flange orientation and location! These mufflers are designed to fit as high as possible for maximum ground clearance! These mufflers are NOT QUIET! If you want a "Quiet" muffler you need a "Turbo" muffler or Quiet Pack.
EMPI: If you have an EMPI Merged Header, you should know that they have changed their header design. The new design had the collector flange perpendicular with the ground (Straight up and down). The OLD EMPI design had the flange aiming toward the ground at a 10 degree angle. So the NEW Design fits the A-1-500M-2.5, and the OLD design fits this A-1-100M-2.5.
|
|
|
|
|
|
|
|
|
|
|
A-1 Performance Phat Boy Magnaflow MUFFLER, Fits Small Flange Bugpack Street Headers (2031-10 and 2031-13)
|
|
|
A-1 Performance Phat Boy Magnaflow Muffler, Small Flange Bugpack Street Headers (2031-10 and 2031-13), Perpendicular Flange with Top Bolt in 1 o'clock position. The finest muffler available for your VW, it's made to fit YOUR CAR! (not one size fits none!). The variations in the different models are slight but they are what make this one fit perfect and not just "OK".
|
|
|
|
|
|
|
|
|
|
|
A-1 Performance Phat Boy Turbo MUFFLER, fits Small Flange Empi, Phoenix, and Berg Non-Merged Headers
|
|
|
A-1 Performance Phat Boy Turbo Muffler, Small Flange Empi, Phoenix, and Berg Non-Merged Headers is the finest muffler available for your VW, it's made to fit YOUR CAR! These headers have heater boxes or J-pipes. This Turbo Muffler is nice and quiet, and is good to around 120hp! This muffler fits the headers which have heater boxes or J-pipes. Please triple check what header you have, there are MANY different headers out there, they all vary slightly in their muffler flange orientation and location! These mufflers are designed to fit as high as possible for maximum ground clearance!
|
|
|
|
|
|
|
|
|
|
|
A-1 Performance Phat Boy Magnaflow MUFFLER, fits Small Flange Empi, Phoenix, and Berg Non-Merged Headers
|
|
|
A-1 Performance Phat Boy Magnaflow Muffler, Small Flange Empi, Phoenix, and Berg Non-Merged Headers is the finest muffler available for your VW, it's made to fit YOUR CAR! These headers have heater boxes or J-pipes. Please triple check what header you have, there are MANY different headers out there, they all vary slightly in their muffler flange orientation and location! These mufflers are designed to fit as high as possible for maximum ground clearance! These mufflers are NOT QUIET! If you want a "Quiet" muffler you need a "Turbo" muffler or Quiet Pack.
|
|
|
|
|
|
|
|
|
|
Single Quiet Pack Muffler for Street-Header-T1, All Beetles, Ghias, and Busses to 1971
|
|
|
This Single Quiet Pack muffler fits our Street-Header-T1, and is shaped to properly fit Beetles, Ghias, THINGs, and Busses with the VW upright engine. The Single QP is a nice quiet muffler that offers better ground clearance than the Phat Boy. The Single QP is a nice quiet muffler that offers better ground clearance than the Phat Boy. This is a classic muffler design that puts the exhaust tip on the right side of the car. The Single Quiet Pack is quiet and flows pretty well, much quieter than the Dual Quiet Pack muffler. This is a nice quiet muffler, good to about 80hp before back pressure starts to take away engine power. At that point you should consider a Dual QP, Hideaway, Mondo Muffler, or Phat Boy.
|
|
|
|
|
|
|
|
|
|
Heater Box Replacement Pipes (J-pipes), Type 1, 1 3/8", Ceramic Silver, PAIR, 1530-PC
|
|
|
Heater Box Replacement Pipes (J-pipes), Type 1, 1 3/8", Ceramic Silver, PAIR, 1530-PC are used when removing your stock heater boxes off your vw beetle, ghia, or Thing, and replace them with a light and inexpensive J-pipe. Price is for a pair to do both sides on 1 engine. These are ceramic coated for long-term good looks.
Note: these J-pipes do NOT have the tabs to bolt the lower Sled Tins to the J-pipes.
|
|
|
|
|
|
|
|
|
|
EMPI Glasspack Muffler w/Chrome Tip for VW Bug, Ghia, and Type 2, 00-3663-0
|
|
|
Glasspack Muffler w/Chrome Tip for VW Bug, Ghia, and Type 2, 00-3663-0 is a great street muffler if you don't want to be known as the #)#*&)*& driving around with that open exhaust, but want a LITTLE "Identity"; Get a Glasspack! These have Unique "VW Sound".Not too loud, and not too quiet, an in-between noise-level that is a great compromise.
|
|
|
|
|
|
|
|
|
|
Heater Box Replacement Pipes (J-pipes), Type 1, 1 3/8", PAIR
|
|
|
Heater Box Replacement Pipes (J-pipes), Type 1, 1 3/8", PAIR are used when removing your stock heater boxes off your vw beetle, ghia, or Thing, and replace them with a light and inexpensive J-pipe. Price is for a pair to do both sides on 1 engine.
Note: these J-pipes do NOT have the tabs to bolt the lower Sled Tins to the J-pipes.
|
|
|
|
|
|
|
|
|
|
Lower Engine Tin (Sled Tins, Heater Channel Tins), Upright Engines, 3 Piece Set, CHROME
|
|
|
Lower Engine Tin (Sled Tins, Heater Channel Tins), Upright Engines, 3 Piece Set, CHROME fits between heater box and crank case on either side helps protect the push rod tubes and prevents overheating. These are REQUIRED for best cooling and thermostat operation. This is the chrome version for buggies and show cars. You MUST keep these waxed or they'll rust quickly!These protect the push rod tubes from debris, and also funnel hot air (that already cooled the engine) down and away from your engine. They also keep the thermostat warm so the thermostat is reading a true hot air exhaust temperature, rather than being cooled by rushing air as you go down the road, which closes the flaps because the thermostat thinks the engine is "too cold". We cannot stress the importance of these 3 pieces of cooling tin, even if you do not have a thermostat and flaps. If these are not there, air backs up under the engine and the fan has a harder time blowing cooling air over the cylinders and heads due to the pressure increase below. These fit 40hp through 1600cc upright engines.
|
|
|
|
|
|
|
|
|
|
Industrial Cooling Tins (Heat Shields), For Heater Box Removal on 1958-74 Upright Engines, PAIR
|
|
|
Industrial Cooling Tins, For Heater Box Removal on 1958-74 Upright Engines, PAIR are used when you use J-pipes to replace the stock heater boxes. These fill the gaps that show up when you took the heater boxes off! These are critical for proper cooling, and are used along with the lower sled tins. These are CNC Laser cut from 20ga steel, then bent, and actually TEST FIT, and after fitment is verified they are then blasted and powder coated Satin Black.
|
|
|
|
|
|
|
|
|
|
VW Stinger, Small 3 Bolt Flange
|
|
|
These stingers fit the small 3 bolt flanges on Bugpack, EMPI, Phoenix, Berg, and S&S systems. Choose from Raw/Black, Chrome, or Ceramic Silver. Stingers eliminate back pressure, and in fact due to their tapered shape, they increase scavenging of the exhaust system and cylinder.These stingers fit the small 3 bolt flanges on Bugpack, EMPI, Phoenix, Berg, and S&S systems. Choose from Raw/Black, Chrome, or Ceramic Silver.
|
|
|
|
|
|
|
|
|
|
"Street Tubes" Replacement Muffler
|
|
|
This is JUST the replacement muffler portion of the Street Tubes Muffler Kit, if yours is in need of replacement.
|
|
|
|
|
|
|
|
|
|
Lower Engine Tin (Sled Tins, Heater Channel Tins), Upright Engines, 3 Piece Set
|
|
|
Lower Engine Tin (Sled Tins, Heater Channel Tins), Upright Engines, 3 Piece Set fits between heater box and crank case on either side helps protect the push rod tubes and prevents overheating. These are REQUIRED for best cooling and thermostat operation.These protect the push rod tubes from debris, and also funnel hot air (that already cooled the engine) down and away from your engine. They also keep the thermostat warm so the thermostat is reading a true hot air exhaust temperature, rather than being cooled by rushing air as you go down the road, which closes the flaps because the thermostat thinks the engine is "too cold". We cannot stress the importance of these 3 pieces of cooling tin, even if you do not have a thermostat and flaps. If these are not there, air backs up under the engine and the fan has a harder time blowing cooling air over the cylinders and heads due to the pressure increase below. These fit 40hp through 1600cc upright engines.
|
|
|
|
|
|
|
|
|
|
Oxygen Sensor Adapter Pipe, Small 3 Bolt Flange
|
|
|
This slick adapter bolts between the muffler and header, and has an O2 bung welded in the side. This is designed for TEMPORARY use for engine tuning. By using this part you can tune many different cars without welding an O2 bung into each one. This adapter is 2 1/4" long from flange to flange, has a 1 1/2" ID Pipe (that will need weld cleanup if you want it perfect), and uses the VW Industry standard small bolt flange of 2 5/16" Center to Center bolt spacing.This part does NOT come with any exhaust flange gaskets, you will need 2 good ones to make sure it doesn't leak! If it leaks, you'll get "False Lean" readings on your O2 Gauge!
|
|
|
|
|
|
|
|
|
|
Vintage Speed Stainless Steel Flare Flanges (Use Stock Heater Boxes or J-pipes with Flanged VS Mufflers), 155-200-FF100
|
|
|
Vintage Speed Stainless Steel Flare Flanges (Use Stock Heater Boxes or J-pipes with Flanged VS Mufflers), 155-200-FF100 are used with the VS Mufflers and stock heater boxes or J-pipes. Normally the VS Muffler uses flanged J-pipes or heater boxes. You'll use a stock muffler kit when using these adapters on the VW mufflers.
|
|
|
|
|
|
|
|
|
|
Heater Box & J-pipe to Header/Muffler Flange Kit
|
|
|
Heater Box & J-pipe to Header/Muffler Flange Kit is one of the best improvements you can do to your VW! Stock exhaust doughnuts leak like crazy, especially with headers which are not even close to rigid!
Simply cut off the flare on the muffler or header, then slip these on during assembly. Weld or braze one flange to the heater box or j-pipe, and the other to the muffler or header. Now you have a leak-free connection!
|
|
|
|
|
|
|
|
|
|
Stinger Baffle, Stinger Insert, Muffler Insert for Stingers, 13 1/2" Long, 2 13/16" End
|
|
|
Stinger Baffle, Stinger Insert, Muffler Insert for Stingers, 13 1/2" Long, 2 13/16" End is a fiberglass packed baffle that makes a vw exhaust stinger as quiet as it can be. Some people tack weld them in place, others put a set-screw through the rim to keep it in place and to prevent it from vibrating and rattling in the exhaust!.This baffle fits all the stingers for exhausts smaller than 1 5/8".
|
|
|
|
|
|
|
|
|
|
18" Long Heater Hose, Black Cardboard, PAIR, 028-129-087A-113-292C
|
Price: $18.95
SALE ITEM! use code TOOMANY30
|
|
|
18" Long Heater Hose, Black Cardboard, PAIR, 028-129-087A-113-292C are the flexible black heater hose which runs from your fan shroud outlets to your pre-heater tubes on your stock muffler. These are more durable than the silver hoses, and hide oil and dirt too!
|
|
|
|
|
|
|
|
|
|
Copper Exhaust Flange Gaskets, Set of 4
|
|
|
The finest exhaust gaskets available for your beetle or bus engine, and are available in 3 sizes for many applications! These fantastic gaskets will NOT blow out! They can also be installed WITHOUT removing the header! Notched bolt holes allow easy installation. Sold in set of 4 gaskets. These are stamped out of copper, and ensure a positive seal every time. They are also REUSABLE. Simply heat them with a torch til' they glow red, then allow them to air cool (slowly). This makes them soft again (annealing) so you can reuse them.
|
|
|
|
|
|
|
|
|
|
O2 Sensor Bung and Plug, Stainless Steel (18 x 1.5mm Threads)
|
|
|
O2 Sensor Bung and Plug, Stainless Steel (18 x 1.5mm Threads) is designed for you to weld to your exhaust system to repair or install an O2 sensor to FI closed loop operation, or for detailed wideband tuning. Stainless Steel for SS exhausts!
|
|
|
|
|
|
|
|
|
|
Graphite Compression Exhaust Gaskets, 1 3/8, 1 1/2, and 1 5/8", Set of 4
|
|
|
Graphite Compression Exhaust Gaskets, 1 3/8, 1 1/2, and 1 5/8", Set of 4 start off at 1/8" thick, but crush to 1/16", filling the void created by warped or pitted flanges. These seal TIGHT against the sealing surface so they do not leak!
|
|
|
|
|
|
|
|
|
|
|
Exhaust Installation Kit, Economy
|
|
|
This great little kit includes what you need to install that new vw bug header or stock muffler onto your vw beetle or bus! It includes all new clamps, gaskets, seals, exhaust doughnuts, and hardware necessary to install all sorts of exhaust systems. This kit is designed to work on upright and type 3 engines, NOT type 4 engines. 1968-71 bus engines should use the bus specific kit, since the Mustache Bar really eats away room for using these 2 piece clamps, the bus specific kit uses 1 piece clamps that work better.
|
|
|
|
|
|
|
|
|
|
13mm Curved Wrench (S-wrench)
|
|
|
13mm Curved Wrench (S-wrench) is the perfect tool for removing and installing stock VW Bug carburetors, or working on pesky heater boxes and exhaust systems! This tool curves around obstructions to make the first loosen, or final tighten a breeze! This tool is a must in every VW Enthusiast's Tool Box.
|
|
|
|
|
|
|
|
|
|
O2 Sensor Bung and Plug, Mild Steel (18 x 1.5mm Threads)
|
|
|
O2 Sensor Bung and Plug, Mild Steel (18 x 1.5mm Threads) is designed for you to weld to your exhaust system to repair or install an O2 sensor to FI closed loop operation, or for detailed wideband tuning.
|
|
|
|
|
|
|
|
|
|
12 Point Engine Nuts, 8 x 1.25mm Thread, Set of 8, 4101-10
|
Price: $12.95
SALE ITEM! use code TOOMANY30
|
|
|
12 Point Engine Nuts, 8 x 1.25mm Thread, Set of 8, 4101-10 are a great looking 12pt black finished nut to set off your engine. Precision made from a hard steel, the 12pt 10mm head gives extra grip with 12pt sockets so they don't round off. These have a 8 x 1.25mm thread to fit your intake and exhaust studs, for easier installation and removal of dual carb systems, and performance exhausts.
|
|
|
|
|
|
|
|
|
|
Steel Reinforced Exhaust Flange Gaskets, Set of 4
|
|
|
The finest conventional exhaust gaskets available for your beetle or bus engine, and are available in 2 different sizes. This is a set of 4 gaskets to do one engine. This is a premium gasket for a budget price! The gasket material is reinforced with steel to prevent gasket blow-out.
|
|
|
|
|
|
|
|
|
|
18" Long Silver Heater Hose (2" I.D.) 028-129-087F, PAIR
|
|
|
This pair of flexible silver heater hose runs from your fan shroud outlets to your heater boxes, or your pre-heaters on your stock muffler.
|
|
|
|
|
|
|
|
|
|
Permatex Ultra Copper RTV Sealant (Silicone), 3oz Tube
|
|
|
Permatex Ultra Copper RTV Sealant (Silicone), 3oz Tube is an excellent sealant for cylinder bases, and cylinder shims. Wipe on a thin coat, let it skin up then install the parts. Also great for valve cover gaskets, oil strainer and generator stand gaskets, etc. Permatex makes several different formulations of RTV, we only carry 2 of them because these 2 cover all applications that we need for our Vintage VWs. The COPPER is the best for high heat applications, like exhaust systems. If you don't want to use a gasket (or can't get one fast enough), just wipe a skim coat of the Copper on, and let it skin up, then assemble the parts. It will also seal up some unevenness in the flanges, or other situations that can create exhaust leaks.
The GRAY is the most oil resistant of the Permatex RTV Line. So it's best used for any area that will get exposed to engine oil or grease. Cylinder bases, oil pump base gaskets, oil strainer gaskets, valve cover gaskets, generator stand gaskets, etc.
Both are a must to have in the toolbox!
|
|
|
|
|
|
|
|
|
|
Plastic Heater Hoses, Upright Engines, PAIR
|
|
|
Plastic Heater Hoses, Upright Engines, Pair, are fantastically good looking and durable black plastic heater hoses that run from your fan shroud outlets to your heater boxes, or your pre-heaters on your stock muffler.
|
|
|
|
|
|
|
|
|
|
Stainless Steel O2 BUNG (only)
|
|
|
|
|
|
|
|
|
|
|
|
|
Graphite Flange Exhaust Gaskets, EACH
|
|
|
Graphite Flange Exhaust Gaskets, EACH are specifically engineered to handle the extreme heat and pressures of a high performance engine. These gaskets start off at 1/8" thick, but crush to 1/16", filling the void created by warped or pitted flanges. These seal TIGHT against the sealing surface so they do not leak!
|
|
|
|
|
|
|
|
|
|
Copper Locking Exhaust Nut Kit, 8 Pieces
|
|
|
These Locking Exhaust Nuts will go on but not loosen! Set of 8 to do all 4 exhaust ports.
|
|
|
|
|
|
|
|
|
|
Heater Box Repair Pipe, EACH, 113-255-107REP-2509
|
|
|
Heater Box Repair Pipe, Each, 113-255-107REP-2509 is a fast and inexpensive way to repair leaky stock heater boxes. Slip this part over the outlet tube (after cutting off any cancerous section), then weld or braze it to form a tight seal, and reassemble.
|
|
|
|
|
|
|
|
|
|
Barrel Clamp, Accelerator Cable and Heater Box Cable, Flat Blade Head, 8 x 12mm, Pack of 5 Clamps, 311-129-777
|
Price: $6.95
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
Barrel Clamp, Accelerator Cable and Heater Box Cable, Flat Blade Head, 8 x 12mm, Pack of 5 Clamps, 311-129-777 is used at the stock carburetor to throttle cable, and at the heater cable to heater box lever. These often get lost or damaged, having spares is a good idea! This version with the flat blade head is preferred by many because they can quickly tighten or loosen it with a screwdriver, instead of finding that pesky 8mm wrench!
|
|
|
|
|
|
|
|
|
|
Barrel Clamp HEX head, for Accelerator Cable and Heater Box Cable, 8 x 12mm, Pack of 5, 111-129-921
|
|
|
Barrel Clamp, Accelerator Cable and Heater Box Cable, 8 x 12mm, Pack of 5, 111-129-921 are used at the stock carburetor to throttle cable, and at the heater cable to heater box lever. These often get lost or damaged, having spares is a good idea!
|
|
|
|
|
|
|
|
|
|
O2 Sensor Plug, Mild Steel (18 x 1.5mm Threads)
|
|
|
O2 Sensor Plug, Mild Steel (18 x 1.5mm Threads) is designed for you to plug the threaded bung up when you don't have the O2 sensor installed for whatever reason (IE: You are finished tuning). You can save wear/tear on the O2 sensor by saving it!
|
|
|
|
|
|
|
|
|
|
Copper Small Flange Muffler/Stinger Gasket, EACH
|
|
|
Sick of VW Beetle Exhaust Gaskets blowing out? Use these all-metal copper ones and eliminate that problem for good! You can even re-use these! These fantastic gaskets will NOT blow out! Sold per each, it will last a LONG TIME! The finest header gasket available for your beetle or bus engine!These are stamped out of copper, and ensure a positive seal every time. They are also REUSABLE. Simply heat them with a torch til' they glow red, then allow them to air cool (slowly). This makes them soft again (annealing) so you can reuse them.
|
|
|
|
|
|
|
|
|
|
Non-Metal "Econo" Exhaust Gaskets, 1 3/8" & 1 5/8", Set of 4
|
|
|
These gaskets are manufactured from heat resistant materials for long life, but they generally need to be replaced when you remove the exhaust after its been run for a while (as opposed to the metal-reinforced ones which can be re-installed). They are precision die cut in 1 3/8" and 1 5/8" sizes for your exhaust. These are the Non-Metal "Econo" exhaust gaskets, the budget-conscious choice.
|
|
|
|
|
|
|
|
|
|
Baja 2 Bolt Header/Muffler Gaskets, Set of 2
|
|
|
These fit the 2 bolt flange Baja systems. These gaskets are manufactured from heat resistant materials for long life. They are precision die cut for your exhaust. Good budget exhaust gaskets when you can't afford copper. Set of 2 so you have a spare! Fits 2055-10, 2056-10, 2524, 2527, and 2528.
|
|
|
|
|
|
|
|
|
|
Preheater to Muffler Gasket (Preheater Gasket), Dual Pre-heater Upright Engine, 1974 California Model Beetle, Super Beetle, and Karmann Ghia, 113-251-263B per EACH
|
Price: $3.95
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
Preheater to Muffler Gasket (Preheater Gasket), Dual Pre-heater Upright Engine, 1974 California Model Beetle, Super Beetle, and Karmann Ghia, 113-251-263B is the gasket that goes between the preheat flange on the muffler on these rare models. is the gasket that goes between the dual preheat flange on the muffler, and the preheat pipe on the intake manifold. 2 are needed to do one engine.Having a couple spares is a wise idea, these are very difficult to find! Price is for one gasket.
|
|
|
|
|
|
|
|
|
|
Doughnut Gasket (Exhaust Seal Ring), 13-1600cc Engines, 111-251-241A
|
Price: $3.95
SALE ITEM! use code TOOMANY30
|
|
|
Doughnut Gasket (Exhaust Seal Ring), 13-1600cc Engines, 111-251-241A is great when the ONLY thing wrong with your muffler kit is the cheesy doughnut rings blew out! These are high quality, not like those Brazilian or Chinese pieces of junk!
|
|
|
|
|
|
|
|
|
|
Small Flange Muffler/Stinger Gaskets, PAIR, 2518
|
|
|
Small Flange Muffler/Stinger Gaskets, PAIR, 2518 are manufactured from heat resistant materials for long life. They are precision die cut for your exhaust. Good budget exhaust gaskets when you can't afford copper. Set of 2 so you have a spare!
|
|
|
|
|
|
|
|
|
|
|
Tri-Mil Small Flange Muffler/Stinger Gaskets, EACH
|
|
|
Tri-Mil Small Flange Muffler/Stinger Gaskets, EACH are manufactured from heat resistant materials for long life. They are precision die cut for your exhaust. Good quality gasket, with a metal sandwich construction! You should keep a spare in your garage for when (not IF) they blow out and you need to replace it.
|
|
|
|
