|
|
|
|
|
|
Shock Absorber Bolt and Nut, 12 X 1.75 X 100mm
|
|
|
High Grade 12 X 1.75 X 100mm Bolt and Nut for completing your Shock Absorber Installation.
|
|
|
|
|
|
|
|
|
|
Shock Boss, 12 X 1.5mm X 2" Long, EACH, 17-2714-0
|
|
|
Shock Boss, 12 X 1.5mm X 2" Long, EACH, 17-2714-0 is a precision threaded steel boss for welding to the location of your choosing. This is a MUST when adding additional shocks per wheel. Extra thick shoulder to make your welding easy! Threading is inset to prevent shearing. 12 X 1.5mm X 2" Long.
|
|
|
|
|
|
|
|
|
|
Shock Boss, 12mm X 1" X 1.780" Long, Unthreaded, EACH, 17-2712-0
|
|
|
Shock Boss, 12mm X 1" X 1.780" Long, Unthreaded, EACH, 17-2712-0 is a steel boss UNTHREADED inside for welding to the location of your choosing. This is a MUST when adding additional shocks per wheel. Extra thick shoulder to make your welding easy! 12mm ID for Through Bolt Use. 12 X 1" X 1.780" Long
|
|
|
|
|
|
|
|
|
|
KYB EXCEL-G (formerly GR-2) Low Pressure Gas Shock Absorber, 1952-65 Std Beetle (Link Pin) Front, 1955-79 Type 2 Front, Type 3 Front, and ALL T1 & T3 Rear, per EACH
|
|
|
KYB GR-2 shock absorbers feature their patented Floating Dividing Piston that separates gas & fluid. The pressure of the gas in the shock prevents oil foaming, but with the Stiffness and Spring Effect present in High-Pressure Gas Shocks.We strongly recommend these over the STIFF White Gas-A-Just KYBs.
|
|
|
|
|
|
|
|
|
|
Rear Shock Absorber, 49-68 Type 1, 55-67 Type 2, 62-68 Type 3, 113-513-031G BRAZIL or MEXICO
|
|
|
Rear Shock Absorber, 49-68 Type 1, 55-67 Type 2, 62-68 Type 3, 113-513-031G are an excellent quality shock for the money. We prefer non-gas shocks for the stockish VW beetles and busses because these ride SO much better than the gas shocks!
|
|
|
|
|
|
|
|
|
|
VW Rear Chassis Dolly (Frame Horn Dolly)
|
|
|
Rear support fits all Type 1 bugs, sandrails, and bajas. Lets you move your car when both engine and swing axle transaxle are removed. All steel construction and powder coated with 6” caster.This bolts to the end of your frame horns and allows you to roll it around your shop with the trans axle out!
|
|
|
|
|
|
|
|
|
|
KYB Gas-A-Just Shock Absorber, T1 ALL REAR, 1955-67 Type 2 Rear, Type 3 ALL Rear
|
|
|
KYB Gas-Charged shock absorbers feature their patented Floating Dividing Piston that separates gas & fluid. The pressure of the gas in the shock prevents oil foaming, but it also acts as a "spring" and will raise the front of your car and make it stiffer.Fits: Type 1 Rear (All years), 1955-67 Type 2 Rear, Type 3 (ALL) Rear
|
|
|
|
|
|
|
|
|
|
Coil Over Shocks, Eye/Eye, PAIR, 6505
|
|
|
Coil Over Shocks give additional "Spring" to the axle you are installing them on. Fully adjustable design allows you to set your suspension to suit your needs. Helps overcome "Sag" from old torsion bars, without full suspension disassembly. This is for a pair of shocks to do the rear axle. The eye to eye length is 17" extended. I have no way to compress it to measure the compressed length.
|
|
|
|
|
|
|
|
|
|
Koni Adjustable REAR Shock Absorber, Swing Axle Type 1, 2, and 3, EACH, 80-1350
|
|
|
Koni Adjustable REAR Shock Absorber, Swing Axle Type 1, 2, and 3, EACH, 80-1350 are a fully adjustable oil shock, so you can set the damping for your car and your ride preference! These are the finest shocks available for your street or race car!
|
|
|
|
|
|
|
|
|
|
RLR Single Adjustable 50/50 Rear Shocks, PAIR
|
|
|
RLR Single Adjustable 50/50 Rear Shocks, PAIR are THE most overlooked component on a pan-based drag car! With these you will dramatically lower your 60' times, and be more consistent too! A simple twist of the dial and you'll compensate for the new track! No more bouncing off the snubbers! No more peg-legging down the track! No more massive changes in air pressure to try to get the results you need!
|
|
|
|
|
|
|
|
|
|
RLR Double Adjustable 50/50 Rear Shocks, PAIR
|
|
|
RLR Double Adjustable 50/50 Rear Shocks, PAIR are THE most overlooked component on a pan-based drag car! With these you will dramatically lower your 60' times, and be more consistent too! A simple twist of the dial and you'll compensate for the new track! No more bouncing off the snubbers! No more peg-legging down the track! No more massive changes in air pressure to try to get the results you need!
|
|
|
|
