|
|
|
|
|
|
6 x 12mm Hex Bolt, Full Thread, EACH, N102123
|
Price: $0.25
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
6 x 12mm Hex Bolt, Full Thread, Each, N102123 are the same size as the screws that hold the VW Engine Tin in place, but with a 10mm hex head on it rather than a flat blade slot. You can use these all over the VW, and the hex head is easier to tighten! These often vibrate loose, have spares!
|
|
|
|
|
|
|
|
|
|
6 x 1 x 12mm Sheet Metal Screw w/LARGE Washer (Cheese Head), EACH
|
Price: $0.35
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
6 x 1 x 12mm Sheet Metal Screw w/LARGE Washer (Cheesehead), Each has a super huge washer, used to cover up sheet metal holes, gaps, or tears around the threaded insert. They replace the regular sheet metal screws which are 6 x 1 x 12mm which hold the VW Engine Tin in place. They are used Extensively throughout the engine, securing the tin and backing plates in place. These often vibrate loose, have spares!
|
|
|
|
|
|
|
|
|
|
6 x 12mm Sheet Metal Screw w/Washer (Cheesehead), EACH, N107101
|
Price: $0.40
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
6 x 12mm Sheet Metal Screw w/Washer (Cheesehead), Each, N107101 are the screws that hold the VW Engine Tin in place. They are used Extensively throughout the engine, securing the tin and backing plates in place. These often vibrate loose, have spares!
|
|
|
|
|
|
|
|
|
|
6 x 12mm Sheet Metal Screw w/Washer (Phillips Pan Head), EACH, N107101-PHILLIPS
|
Price: $0.50
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
6 x 12mm Sheet Metal Screw w/Washer (Phillips Pan Head), Each, N107101-PHILLIPS are the screws which hold the VW Engine Tin in place. They are used Extensively throughout the engine, securing the tin and backing plates in place. The Phillips version was used on the Type 4 engine since it is much easier to install in hard-to-access places. But using them on the upgright engine has benefits too!
|
|
|
|
|
|
|
|
|
|
Grub Screw Retaining Nut, 111-411-155
|
Price: $2.50
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
Grub Screw Retaining Nut, 111-411-155 is the lock nut that keeps the Grub Screw from loosening. These are exposed to rode grime and SALT, and do get gnarled up when "mechanics" us the wrong tools to tighten and loosen it.
|
|
|
|
|
|
|
|
|
|
Torsion Arm Grub Screw, 111-411-151
|
|
|
Torsion Arm Grub Screw, 111-411-151 is the threaded screw that keeps the front trailing arm secured to the torsion leaves in the front. If this is loose the front end can fall apart! This MUST be in good shape, and tightened properly, to drive safe. There are 6 of these on each car, one at each trailing arm, and one more in the center of each tube of the axle beam, holding the leaf springs side to side.
|
|
|
|
|
|
|
|
|
|
Stainless Steel Button Head Fan Shroud Screws, 34 Pieces (Sheet Metal Screws)
|
|
|
Stainless Steel Button Head Fan Shroud Screws, 34 Pieces (Sheet Metal Screws) are Stainless steel Button Head (Rounded Top with Allen Head) screws don't rust and really dress up your fan shroud and engine!
|
|
|
|
|
|
|
|
|
|
Fan Shroud Flap Hardware Kit, Non-Doghouse (In Shroud Oil Cooler), 19pc Kit
|
|
|
Fan Shroud Flap Hardware Kit, Non-Doghouse (In Shroud Oil Cooler), 19pc Kit includes (4) Spring Clips, (4) 6mm Clip Washers, (8) Flap Retaining Screws, (1) SS Tension Spring, (1) 8x13mm Thermostat Bolt, and (1) 8mm Thermostat Washer!
|
|
|
|
|
|
|
|
|
|
Fan Shroud Flap Hardware Kit, Doghouse Shroud(Offset Oil Cooler), 23pc Kit
|
|
|
Fan Shroud Flap Hardware Kit, Doghouse Shroud(Offset Oil Cooler), 23pc Kit includes (6) Safety Clips, (6) 6mm Clip Washers, (8) Flap Retaining Screws, (1) SS Tension Spring, (1) 8x13mm Thermostat Bolt, and (1) 8mm Thermostat Washer!
|
|
|
|
