Once you use these you will never EVER go back to the Brass Nuts (that strip and round off), or the barely better 12mm ones out there.

These are a LOT smaller than 11mm on the Head, and the flange keeps the header far enough away from the nut to allow your socket or wrench head enough room to get on and off!

We use these all over because they are so useful. The obvious application is header nuts, when you have a larger than stock header. These even work on exhausts as big as 2 1/4"!!!!! The not so obvious application are to hold down your intake manifold(s)! Now you have a ton of room to use a FAST Ratchet with a long extension above the carb top! You can take a dual carb system off in under a minute after a little practice! Imagine, no more bloody knuckles after an hour of fighting your car!!!!

NOTE: These are genuine WEBER parts, not a cheap chinese copy.

Proper idle settings are achieved by fully warming up the engine, set your ignition timing, then sync the carbs. Next adjust idle mixture, then idle speed, idle mixture, idle speed, and idle mixture. At this point you are likely not changing anything and you are done!

To set idle mixture, turn the idle mixture screw to fastest idle speed. it's best to turn it in too far 1 bbl at a time (bottom it out lightly, idle speed will drop as you lose a cylinder), and as you turn it out the cylinder will come back, picking up idle speed. Set for fastest idle, + 1/2 turn out (richer). The extra 1/2 turn makes for a more STABLE idle (not a better one).

Note that any time you change the idle speed, carb sync, idle jet size, or ignition timing, you must re-set the idle mixture!

Proper idle mixture setting is achieved by fully warming up the engine, set your ignition timing and idle speed. Turn the idle mixture screw to fastest idle speed. it's best to turn it in too far 1 bbl at a time (bottom it out lightly, idle speed will drop as you lose a cylinder), and as you turn it out the cylinder will come back, picking up idle speed. Set for fastest idle, + 1/2 turn out (richer). The extra 1/2 turn makes for a more STABLE idle (not a better one).

Any tmie you change the idle speed, carb sync, idle jet size, or ignition timing, you must re-set the idle mixture!

Hose clamps are not even needed, because the cloth woven on the hose surface acts like a "Chinese finger trap", and keeps the hose tight on the fitting. Some owners choose to err on the side of caution and use clamps also.

Price is for a meter of hose.

This book is KILLER on understanding the operation of the Weber carburetor!

Jet Drill (Jet Reamer Kit), .30-2.00mm (30-200 in Jet Size), 30pc Kit is not as good as using the proper sized jet, but drilling is acceptable if you go VERY slowly, and after you arrive at your proper jet size, measure and order the proper indexed jets!

This tool includes jet pins in these sizes: .45, .50, .55, .60, .65, .70, .75, .80, .85, 1, 1.05, 1.10, 1.15, 1.20, 1.25, 1.30, 1.40, and 1.50mm.

This kit includes jet pins in these sizes; 1.50, 1.60, 1.70, 1.80,. 1.90, 2.00, 2.10, 2.20, 2.30, 2.40, 2.50, 2.60, 2.70, 2.80, 2.90, and 3.0mm.

This is a great kit for use with large main jets, and most air jets.

This fits inside the barrel (mouth) of the carburetor. It requires an adapter for non-round "Internal" carb throats such as ICTs and DCNFs. It also requires an adapter for Kadrons due to the centrally located air filter mounting stud.

This is the less expensive ECONO model (made in China or Taiwan), NO GUARANTEE OR WARRANTY ON IT!

This regulator comes with a mounting bracket and hardware, but does NOT have fuel line barbs, which much be purchased separately depending on the size of fuel hose you are using. If you have a single carb, you can simply plug one outlet port on the regulator and run it as just a regulator rather than a Tee also.

Note that proper fuel pressure is critical for proper carburetor operation. Weber IDF, IDA, ICT, DFEV/DFAV, and DCNFs work best with 3-3.5psi, so this regulator works for all of them, even if you switch carburetors sometime in the future!

This is an EXCELLENT regulator to use with the stock fuel pump. Normal methods of dropping fuel pressure with the stock fuel pump are to stack gaskets between the pump and pump spacer, and this does work but it also reduces fuel volume. Using this regulator will keep full volume but wlll drop pressure, which is more desirable.

This fits inside the barrel (mouth) of the carburetor. It requires an adapter for non-round "Internal" carb throats such as ICTs and DCNFs. It also requires an adapter for Kadrons due to the centerally located air filter mounting stud.

This Sync Model is ideal for all velocity stack and carb throats of 1 5/8 to 2 1/8" (40 to 55mm Diameter).

This fits inside the barrel (mouth) of the carburetor, fitting airhorns from 2" (51mm) to 2 5/8" (67mm) in diameter. It requires an adapter to use on the smaller Weber IDF and Dellorto DRLA carburetors.

Fuel Pressure Regulator, Basic, Carbureted Engines, 1.5-5psi is a low pressure fuel pressure regulator that works with most fuels except methanol. Fuel pressure is pre-set to 3.5psi, but it can be set to any fuel pressure between 1.5psi and 5psi. THIS ONE ACTUALLY WORKS, unlike the Purolator, Mr. Gasket, and EMPI Units!

This regulator comes with a mounting bracket and hardware, but does NOT have fuel line barbs, which much be purchased separately depending on the size of fuel hose you are using. This regulator is threaded to 1/8" NPT on both inlet and outlet, and does NOT come with fittings! Buy the fittings you need to match the sizes of your fuel hoses.

Note that proper fuel pressure is critical for proper carburetor operation. Holley regulators are "OK" but don't go below 3psi, and stock carburetors (Solex, Bocar, Brosol, and Kadron) all run best with 1.5-2psi fuel pressure. Weber IDF, IDA, ICT, DFEV/DFAV, and DCNFs work best with 3-3.5psi, so this regulator works for all of them, even if you switch carburetors sometime in the future!

Jet Reamer Kit (Jet Drill Kit), All SIzes are not as good as using the proper sized jet, but drilling and reaming are acceptable if you go VERY slowly, and after you arrive at your proper jet size, measure and order the proper indexed jets!

Fuel Pressure Regulator AND Filter, Combination Unit, Carbureted Engines, 1.5-5psi is a low pressure regulator which works with most fuels except methanol. Output is pre-set to 3.5psi, but can adjusted with the turn of a screw to any pressure between 1.5-5psi. This unit also features a 25 micron stainless steel filter element, which catches sand, rust, dirt, and even water! THIS ONE ACTUALLY WORKS, unlike the Purolator, Mr. Gasket, and EMPI Units!

This regulator comes with a mounting bracket and hardware, the barbs are perfect for 5mm and 7mm hose used on vintage VWs.

This is the finest fuel pressure regulator we have found so far; IT ACTUALLY WORKS!

This regulator comes with a mounting bracket and hardware, and has built in 7mm barbs for the fuel hose inlet and outlet. Locknut and adjusting screw, and full instructions.

Note that proper fuel pressure is critical for proper carburetor operation. Holley regulators are "OK" but don't go below 3psi, and stock carburetors (Solex, Bocar, Brosol, and Kadron) all run best with 1.5-2psi fuel pressure. Weber IDF, IDA, ICT, DFEV/DFAV, and DCNFs work best with 3-3.5psi, so this regulator works for all of them, even if you switch carburetors sometime in the future!

Whether you are desiring maximum HP, or MPG, you need to know your fuel mixture EXACTLY to achieve your goal. This device lets you take the guesswork out!

Complete All-In-One Air/Fuel Ratio Gauge Kit. Includes: Gauge, Silver Bezel, Black Bezel, White Faceplate, Black Faceplate, Bosch Wideband O2 Sensor (LSU4.9), 8 Ft. Sensor Cable (Overall length 10 ft.), Exhaust Bung, Program Cable (Only needed for Datalogging and to change the Fuel Type Setting), and Quick Start Guide/Manual. You will need to download the "Logworks" software from Innovate's website.

Innovate LM-2 Wideband Oxygen Sensor Kit, Basic, 3837 is the new LM-2 "Basic" Kit (Single Wideband O2) ONLY which includes the LM-2 meter, Bosch wide-band oxygen sensor, 8 ft sensor cable, cigarette-lighter power adapter, USB cable for PC connection, weld-in bung and plug, LogWorks software CD, and quick-start guide.