OUR ONLINE CHECKOUT is CLOSED and we are NOT accepting any NEW orders at this time.

We are still fulfilling and shipping previously submitted and/or delayed order requests (as product availability allows) UNTIL NOVEMBER 15th 2022.

But after November 15th, all still pending backordered unshipped items will be automatically CANCELLED **(except for any special ordered drop-shipped or made/machined-to-order items).

Our ability to respond to emails is greatly hampered by being under-staffed during this downsize transition time. But we continue to endeavor to answer email inquiries as best we can. And we will continue responding to emails through until early March 2023 because we are wholly committed to resolving any other issues that may arise from previous sales. It is still UNCERTAIN, but we may re-open a substantially downsized version of our store again in the Spring of 2023.

We sincerely appreciate your patience, understanding during this period of restructuring and/or closing. And a huge thank you to all of you whose support and loyalty we have been the beneficiary of over the 23 years that we have worked diligently to support the information and parts needs of the aircooled VW community!

VW Parts Catalog > Mallory VW Ignition
4 products found
Sort By:
1
MSD CDI Ignition Box (Capacitive Discharge Ignition), Basic Unit, Digital Ignition, 6201M
MSD CDI Ignition Box (Capacitive Discharge Ignition), Basic Unit, Digital Ignition, 6201M
Price: $219.95

MSD CDI Ignition Box (Capacitive Discharge Ignition), Basic Unit, Digital Ignition, MSD6201 is basically a device that charges your coil with 400V instead of the measly 12 it normally gets. This results in a bigger spark!

This MSD unit is a direct replacement for Mallory Hyfire VI-A (Hyfire 6-A) PN 6852M (MSD recently bought out Mallory).

With this Capacitive Discharge (CD) system, you will have a stable, uniform spark throughout your engine's rpm range, with no high rpm drop-off like other boxes, or with a standard Kettering Ignition (Points and Condenser, or Points Replacement Device charging the coil with 12 Volts.

This is the basic box, with no programmable rev limiters or 2-step devices, but the spark is identical.

This is compatible with most electronic and magnetic trigger systems.

You must have good quality plug wires, the high energy spark will push them to the limit!

During installation, we recommend you install a 20A fuse between the battery and the CDI unit, and wire the Ground directly to the battery for best results.

 more info
Mallory Unilite Ignition Module, Hand Made, 605
Mallory Unilite Ignition Module, Hand Made, 605
Price: $109.95

Mallory Unilite Ignition Module, Hand Made, 605 is for you guys that fried it by wiring it backwards! This is the highest quality hand made modules. The Unilite module requires a coil impedance of between 1.4 and 3 ohms, CHECK IT! more info
Mallory Hyfire VI MAP Sensor, 2 Bar, 716
Mallory Hyfire VI MAP Sensor, 2 Bar, 716
Price: $64.95

Mallory Hyfire VI MAP Sensor, 2 Bar, 716 is the unit that reads your manifold vacuum and boost, and relays the signal to the Hyfire VI CDI Box. You'll also need the 29785 harness to connect the 2 together. This is the 3 Bar version for up to 15psi. Reading the MAP allows you to set a boost retard in the Hyfire VI CDI Box to prevent detonation under boost conditions. more info
Mallory Firewall Feedthrough (Coil Wire Firewall Feed), EACH, 29001
Mallory Firewall Feedthrough (Coil Wire Firewall Feed), EACH, 29001
Price: $13.95

Mallory Firewall Feedthrough, EACH, 29001 is designed to prevent voltage leaks in passenger compartment mounted coil applications. This provides 1/2 in. of insulation to ensure the spark reaches the distributor. Mounts in a 1" hole with 2 bolts.

These are great when you want to clean up the engine bay, and mount the coil and/or CDI box behind the rear seat, with just a single coil wire running from the firewall to the center of the distributor! more info
   
 
1
SITE USE DISCLAIMER ** READ FOR BEST UNDERSTANDING and USE OF OUR PARTS SERVICE!**

PRODUCT AVAILABILITY can vary and short-term backorders are common. Immediate shipment of requested products is NOT guaranteed. Orders are processed in the order that they are received and order fulfillment time varies.

PRODUCT IMAGES are representative only. Actual product may differ in appearance. Please do NOT rely on PHOTOS while shopping as many of our products have selectable product options that may change the nature of the product being ordered compared to the representative photo. Make your product selections based on the PRODUCT DESCRIPTION and OPTION INFORMATION presented in the detailed product listing.

CATALOG ERRORS: Although every effort has been made to provide accurate pricing and product technical and vehicle application information, THIS CATALOG MAY CONTAIN ERRORS (typographical, photographic, or informational). All information should be verified prior to use.

PRICES are subject to change without obligation. In most cases we are able to honor advertised price, but in the RARE case a substantial price increase occurs, you would be notified and given the option to cancel.

PRODUCT INFORMATION: All information provided by Aircooled.Net (via website or email) is for USE AT YOUR OWN RISK. All products purchased should be inspected, measured, cleaned and properly assembled prior to installation. Since Aircooled.Net has no control over product installation, we will not be held liable for any consequential costs or damages associated with products purchased.