|
|
|
|
|
|
Rear Axle Seal, Fits Inner or Outer, 1968-92 Type 2 (Bus and Vanagon), 211-501-317
|
|
|
Rear Axle Seal, Fits Inner or Outer, 1968-92 Type 2 (Bus and Vanagon), 211-501-317 is used in 2 locations, both inner and outer axle bearing seal in the rear diagonal arm. You must remove the stub axle to change the inner, do this when you are doing CVs!
|
|
|
|
|
|
|
|
|
|
Rear Axle Nut, 46mm, 1964-79 Type 2, 211-501-221A
|
|
|
Rear Axle Nut, 46mm, 1964-79 Type 2, 211-501-221A is the nut that retains your rear brake drum. These MUST be torqued to spec or tighter, or the drum can come loose and really ruin your day. A tight axle nut saves brake drums! Don't confuse these FORGED Axle Nuts with the cheapies many other places are selling, these are very strong and durable, to prevent road-side repairs!
|
|
|
|
|
|
|
|
|
|
46mm Socket for Bus & Vanagon Axle Nuts, 5769
|
|
|
This 3/4" drive 46mm Socket can be used to remove stubborn VW Bus and Vanagon 46mm axle nuts. High Quality tool for repeated use.
|
|
|
|
|
|
|
|
|
|
46mm Axle Nut Removal/Installation Tool
|
|
|
These "Bang" type axle nut removal/installation tools are NOT the preferred method to remove/install the axle nut since they hammer the rear wheel bearing, but they work good enough in the field to get you home!
|
|
|
|
|
|
|
|
|
|
Rear Axle Nut, 46mm, Universal Fit, 1964-79 Type 2, 211-501-221HD
|
|
|
Rear Axle Nut, 46mm, Universal Fit, 1964-79 Type 2, 211-501-221HD is the nut that retains your rear brake drum. These MUST be torqued to spec or tighter, or the drum can come loose and really ruin your day. A tight axle nut saves brake drums!
|
|
|
|
|
|
|
|
|
|
Wheel Bearing (Axle Bearing), Rear Outer, 1971-92 Type 2 (Bus and Vanagon), 211-501-283D
|
|
|
Wheel Bearing (Axle Bearing), Rear Outer, 1971-92 Type 2 (Bus and Vanagon), 211-501-283D is a single bearing in the diagonal arm. You load this with good quality wheel bearing grease. There is also a seal at either end of the diagonal arm!
|
|
|
|
|
|
|
|
|
|
|
Wheel Bearing (Axle Bearing), Rear Inner, 1968-92 Type 2 (Bus and Vanagon), 211-501-287
|
|
|
Wheel Bearing (Axle Bearing), Rear Inner, 1968-92 Type 2 (Bus and Vanagon), 211-501-287 is a single bearing in the diagonal arm. You load this with good quality wheel bearing grease. There is also a seal at either end of the diagonal arm!
|
|
|
|
|
|
|
|
|
|
Axle & Gland Nut Leverage Tool (Buddy Bar)
|
|
|
This tool is used to hold 200 and 180mm flywheels AND 4 or 5 lug brake drums from turning when tightening/loosening. Doesn't risk case breakage (the case ears) like a standard flywheel lock. This is a great tool to have around the garage for the do-it-yourselfer. This tool eliminates the need for an assistant when tightening or loosening rear axle nuts, or the flywheel gland nut. This tool is strong enough to withstand over 2x the recommended torque spec. Bolt pattern fits both 180 and 200mm flywheels, AND both 4 lug and 5 lug brake drums! Also fits 5 x 130mm Small-5 Bus & Vanagon Brake Drums!
|
|
|
|
|
|
|
|
|
|
Wheel Bearing (Axle Bearing), Rear Outer, 1964-70 Type 2, 211-501-283
|
|
|
Wheel Bearing (Axle Bearing), Rear Outer, 1964-70 Type 2, 211-501-283 is a single bearing nearest the wheel (outside). You load this with good quality wheel bearing grease for IRS, but NOT with Swing Axle, since the redux box is full of gear lube! 1968-70 uses wheel bearing grease and 2 grease seals (inside and outside).
|
|
|
|
|
|
|
|
|
|
Flywheel and Brake Drum Torque Tool Kit, 36mm Gland Nut and Axle Nuts
|
|
|
Flywheel and Brake Drum Torque Tool Kit, 36mm Gland Nut and Axle Nuts is used to tighten and loosen the flywheel gland nut, and 36mm Axle Nuts at the brake drum! This was initially introduced under the "Torque-meister" brand name years ago. Mechanical advantage (leverage) makes seemingly impossibly tight nuts come off WITH EASE! Accurate too! This is a great tool to have around the garage for the do-it-yourselfer. This tool eliminates the need for an assistant when tightening or loosening rear axle nuts, or the flywheel gland nut. If you've ever used this, you realize it's a MUST in the garage of the Vee-Dubber!This tool comes with 2 pinion gears, for both 6V/180mm flywheels, AND 12V/200mm flywheels!
|
|
|
|
