|
|
|
|
|
|
Time-Sert Thread Repair Insert, 10 x 1.5 x 24.5mm Long, EACH, 10155
|
Price: $4.00
Item eligible for Econo/1st Class Mail shipment, min ship charge applies
|
|
|
Time-Sert Thread Repair Insert, 10 x 1.5 x 24.5mm Long, EACH, 10155 is the insert for the 10 x 1.5mm Time-Sert when repairing damaged engine mounting studs that have stripped the engine case, to a better than new condition. Inserts are sold per EACH.Time-Sert inserts are superior in every way to typical "Heli Coil" thread repair kits (which are usually wrapped wire, very weak and troublesome to install!).Time-Sert inserts are solid, and also have a flared shoulder that prevents leakage, and locks the insert into place without excessive Loctite needed. The repair process is to drill out the old threads, then use the shoulder cutting tool (To make room for the insert's shoulder on the top), tap the hole, then install the new insert. Hole will be repaired, and will be stronger and better than it was when it was new, due to the larger diameter holding power!
|
|
|
|
|
|
|
|
|
|
Heavy Duty Lifter Bore Cutter Tool (Lifter Boss Cutter) Rental Fee, GB725
|
Rental Fee $20.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Heavy Duty Lifter Bore Cutter Tool (Lifter Boss Cutter) Rental Fee, GB725 is used to clearance the engine case's lifter bores for lifter head clearance. Inadequate clearance is not uncommon with high lift cam shafts, you should have .040" minimum clearance at full lift! As stated in the VW factory bulletin; the cam to cam follower boss clearance is often not enough even if you are using a new stock VW cam with the factory stock cam followers, the engine case radius is often not enough with the lifter under head profile. High lift cams will usually require additional clearancing at the cam follower bosses. This tool is designed to be used in a drill press, but it can easily be used with high quality 1/2" hand drill if you are careful. The high speed tool steel cutter is ground with special angles to cut the boss, and to contour the radius at the same time.
|
|
|
|
|
|
|
|
|
|
Wheel Bearing Race Driver Tool, Rental Fee
|
Rental Fee $20.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Wheel Bearing Race Driver Tool, Rental is a really nice thing to have when you have to install some wheel bearing races into the brake drum or brake rotors. Using a drift can damage the race, then the wheel bearing goes bad quickly! This is easy! Simply find the driver that fits the bearing race, and then you can hit it pretty hard with a hammer to drive it in straight, true, and all the way seated! Kit comes with 10 different sizes of Drivers to fit most any bearing size.Then you can grease and install the bearing, and finish the job knowing it's done right!
|
|
|
|
|
|
|
|
|
|
14mm x 1.25mm Spark Plug Thread Repair Back Tap Tool Rental Fee
|
Rental Fee $25.00
$75 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
14mm x 1.25mm Spark Plug Thread Repair Back Tap Tool Rental is a tool designed to repair 14 x 1.25mm Spark Plug Threads that are just messed up a little bit (not "stripped), with the engine IN THE CAR. This can really save your bacon! Using this tool sure beat R&Ring the engine and then pulling the cylinder heads off! This tool has the correct size and pitch to clean up VW Spark Plug threads that are buggerred up or filled with carbon, it cuts from the combustion chamber OUT, which carries the chips outwards, to keep them out of your engine.
|
|
|
|
|
|
|
|
|
|
Time-Sert Tool Rental Fee, 5/16-24 (Aftermarket Rocker Arm Valve Adjusting Screw), 0562
|
Rental Fee $30.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Time-Sert Tool Rental, 5/16-24 (Aftermarket Rocker Arm Valve Adjusting Screw), 0562 is the best thread repair kit available. This size is typically used to repair damaged adjusting screws in aftermarket rocker arms. Time-Sert tool rental period is one month.
|
|
|
|
|
|
|
|
|
|
Time-Sert Tool Rental Fee, 6 x 1mm (Oil Drain Plate Studs), 1610
|
Rental Fee $30.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Time-Sert Tool Rental, 6 x 1mm (Oil Drain Plate Studs), 1610 is the best thread repair kit available. This size is typically used to repair damaged intake and exhaust studs, as well as the small studs in the engine case. Inserts NOT INCLUDED! The rental period for this kit is: ONE MONTH.
|
|
|
|
|
|
|
|
|
|
Time-Sert Tool Rental Fee, 14 x 1.25mm (14mm Spark Plugs), Standard Repair, 4412
|
Rental Fee $30.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Time-Sert Tool Rental, 14 x 1.25mm (14mm Spark Plugs), Standard Repair, 4412 is the best thread repair kit available. If you have a super loose or super tight spark plug, you will probably need this tool soon! Time-Sert inserts are superior in every way to typical "Heli Coil" thread repair kit. This size is typically used to repair damaged spark plug threads in cylinder heads For this item we recommend Copper Repair Inserts, it is more consistent size-wise, and has better heat transfer, than the steel inserts.The rental period for this kit is: ONE MONTH.
|
|
|
|
|
|
|
|
|
|
Time-Sert Tool Rental Fee, 10 x 1.5mm (10mm Head Stud), Big-Sert Repair, 5015
|
Rental Fee $30.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Time-Sert Tool Rental, 10 x 1.5mm (10mm Head Stud), Big-Sert Repair, 5015 is the best thread repair kit available. This is typically used to repair cylinder head stud threads in engine cases, that have previously pulled a case-saver, the drilled hole is .484" (31/64"). The rental period for this kit is: ONE MONTH.
|
|
|
|
|
|
|
|
|
|
Dual Valve Spring Guide Boss Cutting Tool Rental Fee
|
Rental Fee $30.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Dual Valve Spring Guide Boss Cutting Tool Rental is a tool designed to cut down the valve guide bosses to make room for the inner springs on dual valve springs. You can use this in a drill press, mill, or even a hand drill if you are careful. Just make your cut so the valve spring surface is flat, then be sure to use a DUAL valve spring shim beneath the springs to protect the head from the ends of your valve springs. We include a 9mm shaft so you can also use this cutter on FI Type 1 and Type 4 exhaust guides!
One side of this tool cuts the boss for the inner spring on dual springs, the other side of it is used to trim the top of the valve guide down for more clearance to the retainer. If there is less than .060" clearance between the guide and retainer at full lift, you can bend push rods!
|
|
|
|
|
|
|
|
|
|
Time-Sert Tool Rental Fee, 10 x 1.5mm (Engine Case Mounting Stud), 1015
|
Rental Fee $30.00
$100 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Time-Sert Tool Rental, 10 x 1.5mm (Engine Case Mounting Stud), 1015 is the best thread repair kit available. This size is typically used to repair damaged engine mounting studs that have stripped the engine case. Inserts purchased separately. Inserts NOT INCLUDED! The rental period for this kit is: ONE MONTH.
|
|
|
|
|
|
|
|
|
|
.710" King Pin Reamer, Rental Fee
|
Rental Fee $35.00
$200 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
.710" King Pin Reamer, Rental is used to properly size the bushings AFTER they are pressed in (which squeezes them smaller). This makes the king pins fit PERFECT! A tool like this makes an absolutely miserable job a PLEASURE!This tool is top notch and worth it's weight in Gold! We recommend that you run this reamer through every king pin bushing after it's pressed in, then check the fit of the pin (it should slide in/out smoothly.
|
|
|
|
|
|
|
|
|
|
IRS Diagonal Arm Pivot Jig, PAIR, Tool Rental Fee
|
Rental Fee $65.00
$200 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
IRS Diagonal Arm Pivot Jig, PAIR, Tool Rental is used to hold your IRS Diagonal Arm Pivots in the proper location for you to weld them in place. This ensures the proper geometry and alignment for the finished product!
|
|
|
|
|
|
|
|
|
|
Coil Spring Compressor Tool Rental Fee, KTC-A1047
|
Rental Fee $65.00
$500 Tool Core charged AT TIME OF SHIPMENT (refunded upon return per terms of service)
|
|
|
Coil Spring Compressor Tool Rental, KTC-A1047 is THE easiest and safest way to remove and install coil springs on your VW Super Beetle, Vanagon, or even other makes! Includes 110, 120, and 130mm Jaws to do most models of car, including Macpherson struts! The rental period for this kit is: ONE MONTH. Please note that the core charge/replacement cost for this kit is $500.00, so be sure to return it on time!
|
|
|
|
|
|
|
|
|
|
14mm x 1.25mm Spark Plug Thread Repair Back Tap Tool, USED, PURCHASE
|
|
|
14mm x 1.25mm Spark Plug Thread Repair Back Tap Tool Rental is a tool designed to repair 14 x 1.25mm Spark Plug Threads that are just messed up a little bit (not "stripped), with the engine IN THE CAR. This can really save your bacon! Using this tool sure beat R&Ring the engine and then pulling the cylinder heads off! This tool has the correct size and pitch to clean up VW Spark Plug threads that are buggerred up or filled with carbon, it cuts from the combustion chamber OUT, which carries the chips outwards, to keep them out of your engine.
|
|
|
|
|
|
|
|
|
|
USED Time-Sert Tool Kit PN 0127, 1/8-27 (for fixing Oil Pressure Sending Unit Threads), - FINAL SALE/No Return - INSERTS NOT INCLUDED
|
|
|
USED Time-Sert Tool Kit PN 0127, 1/8-27 (for fixing Oil Pressure Sending Unit Threads), - FINAL SALE/No Return
*This USED tool sale does NOT include any inserts.*
This size is typically used to repair damaged threads in the case at the oil pressure sending unit.
|
|
|
|
|
|
|
|
|
|
|
Big-Sert (Time-Sert) Tool USED, 14 x 1.25mm (14mm Spark Plugs), Super-Duty Repair, 5141S PURCHASE
|
|
|
Big-Sert (Time-Sert) Tool Rental, 14 x 1.25mm (14mm Spark Plugs), Super-Duty Repair, 5141S is the best thread repair kit available. This size is typically used to repair damaged spark plug threads that have already been "fixed" (Heli-coil!) but blew out again! If you have a super loose or super tight spark plug, you will probably need this tool soon! This tool cuts to a 18mm ID, which will repair MOST previously repaired inserts. If you are not sure you should measure yours! Time-Sert inserts are superior in every way to typical "Heli Coil" thread repair kit. This size is typically used to repair damaged spark plug threads in cylinder heads For this item we recommend Copper Repair Inserts, it is more consistent size-wise, and has better heat transfer, than the steel inserts.The rental period for this kit is: ONE MONTH.
|
|
|
|
