|
|
|
|
|
|
Formed Chassis Mounting Tab, 1/2" Hole, 1 1/4"W X 1 3/4"L, Box of 100
|
|
|
When building an off road chassis, you can really uses these weld-on tabs to locate your seat belts, light mounts, etc. These tabs weld into place after you have decided where you want them! This Formed Tab has 20 degree breaks for better weld penetration
|
|
|
|
|
|
|
|
|
|
Universal Chassis Mounting Tab, 1/2" Hole, Box of 100
|
|
|
When building an off road chassis, you can really uses these weld-on tabs to locate your seat belts, light mounts, etc. These tabs weld into place after you have decided where you want them!
|
|
|
|
|
|
|
|
|
|
3-Bolt 1 1/2" Diameter Frame Flange, Set of 10
|
|
|
These flanges are made to incorporate into your chassis, specifically for tubing that you want to be able to remove and re-install after it's built. Engine Access, or simply component installation/servicing. Perfect for designing removable tubing sections!
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Thumb Twist Self Ejecting Stud, Pack of 10
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
|
|
|
|
|
|
Roll Bar Gusset, Box of 100
|
|
|
Most racing associations require gussets in the corners of tubing intersections. These gussets make that task relatively easy for the chassis builder.
|
|
|
|
|
|
|
|
|
|
Buggy and Sandrail Steering Shaft w/Hub Adapter, 60" Long, 7/8" Diameter, EACH
|
|
|
Buggy and Sandrail Steering Shaft w/Hub Adapter, 60" Long, 7/8" Diameter, EACH is the final link between car and driver! This is designed to be used on any chassis or kit car. Long enough for a Bolt-In installation of any custom steering wheel. Made of thick 7/8" diameter tubing. Choose Raw or Chrome.
|
|
|
|
|
|
|
|
|
|
|
2-Bolt 1" Diameter Frame Flange, Set of 10
|
|
|
These flanges are made to incorporate into your chassis, specifically for tubing that you want to be able to remove and re-install after it's built. Engine Access, or simply component installation/servicing. Perfect for designing removable tubing sections!
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Self Ejecting Stud, Pack of 10
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
|
|
|
|
|
|
Tube Bumper, 1.5" OD X 4" Long, PAIR
|
|
|
This Bump Stop is made of tough urethane, to far outlast any rubber or nylon types currently on the market. It is shaped to fit on a section of round tubing. Stops are designed to distribute the load equally. Price is for a PAIR of stops.
|
|
|
|
|
|
|
|
|
|
Steering Hub Bracket, Pack of 25
|
|
|
This is welded to the end of your steering shaft so you can bolt your steering wheel to it!
|
|
|
|
|
|
|
|
|
|
Rear Shock Mounts
|
|
|
This kit allows you to install up to 4 additional shocks in the rear of your VW suspension to control thos off-road terrain! You will have to fabricate the upper shock mounts, but this kit takes care of the lower ones!
|
|
|
|
|
|
|
|
|
|
Steering Shaft Universal Joint
|
|
|
This steering universal joint is a must-have if you are trying to connect your column to a Rack & Pinion style steering box. Fits most "Splined" Style Steering Rack Units. TWO work great with all Center-Mount steering box setups.
|
|
|
|
|
|
|
|
|
|
|
3-Bolt 1 1/2" Diameter Frame Flange, Set of 4
|
|
|
These flanges are made to incorporate into your chassis, specifically for tubing that you want to be able to remove and re-install after it's built. Engine Access, or simply component installation/servicing. Perfect for designing removable tubing sections!
|
|
|
|
|
|
|
|
|
|
|
2-Bolt 1" Diameter Frame Flange, Set of 4
|
|
|
These flanges are made to incorporate into your chassis, specifically for tubing that you want to be able to remove and re-install after it's built. Engine Access, or simply component installation/servicing. Perfect for designing removable tubing sections!
|
|
|
|
|
|
|
|
|
|
Pedal Plate Mount Assembly
|
|
|
This plate allows the builder to mount the VW Pedal Assembly (stock or aftermarket) wherever you want for any custom installation. Can be bolted or welded into place!
|
|
|
|
|
|
|
|
|
|
Tube Bumper, 1.5" OD X 2" Long, PAIR
|
|
|
This Bump Stop is made of tough urethane, to far outlast any rubber or nylon types currently on the market. It is shaped to fit on a section of round tubing. Stops are designed to distribute the load equally. Price is for a PAIR of stops.
|
|
|
|
|
|
|
|
|
|
Shock Boss, 12mm X 1" X 1.780" Long, Unthreaded, EACH, 17-2712-0
|
|
|
Shock Boss, 12mm X 1" X 1.780" Long, Unthreaded, EACH, 17-2712-0 is a steel boss UNTHREADED inside for welding to the location of your choosing. This is a MUST when adding additional shocks per wheel. Extra thick shoulder to make your welding easy! 12mm ID for Through Bolt Use. 12 X 1" X 1.780" Long
|
|
|
|
|
|
|
|
|
|
Bump Stop, 7/8 X 1 7/8 X 1 3/8" w/Center Stud, PAIR
|
|
|
This Bump Stop is made of tough urethane, to far outlast any rubber or nylon types currently on the market. Stops are designed to distribute the load equally. Price is for a PAIR of stops.
|
|
|
|
|
|
|
|
|
|
Bump Stop, Curved Bottom w/Center Stud, PAIR
|
|
|
This Bump Stop is made of tough urethane, to far outlast any rubber or nylon types currently on the market. Stops are designed to distribute the load equally. Price is for a PAIR of stops.
|
|
|
|
|
|
|
|
|
|
Bump Stop, 5/8 X 2 X 2" Square w/Center Stud, PAIR
|
|
|
This Bump Stop is made of tough urethane, to far outlast any rubber or nylon types currently on the market. Stops are designed to distribute the load equally. Price is for a PAIR of stops.
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Tab with Spring, Pack of 10
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
|
|
|
|
|
|
Splined Steering Stub Shaft, EACH
|
|
|
This is designed to weld into your buggy steering shaft, whch then allows to an easy connection to our Steering Universal Joint.
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Spring Retainer, Pack of 10
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
|
|
|
|
|
|
Shock Boss, 12 X 1.5mm X 2" Long, EACH, 17-2714-0
|
|
|
Shock Boss, 12 X 1.5mm X 2" Long, EACH, 17-2714-0 is a precision threaded steel boss for welding to the location of your choosing. This is a MUST when adding additional shocks per wheel. Extra thick shoulder to make your welding easy! Threading is inset to prevent shearing. 12 X 1.5mm X 2" Long.
|
|
|
|
|
|
|
|
|
|
Universal Chassis Mounting Tab, Chromoly Steel, 1/2" Hole, Set of 4
|
|
|
When building an off road chassis, you can really uses these weld-on tabs to locate your seat belts, light mounts, etc. These tabs weld into place after you have decided where you want them!
These tabs are 2 1/4" long the long side, 1 1/2" tall, and have a 1/2" hole.
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Thumb Twist Self Ejecting Stud
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
|
|
|
|
|
|
Shock Absorber Bolt and Nut, 12 X 1.75 X 100mm
|
|
|
High Grade 12 X 1.75 X 100mm Bolt and Nut for completing your Shock Absorber Installation.
|
|
|
|
|
|
|
|
|
|
Formed Chassis Mounting Tab, 1/2" Hole, 1 1/4"W X 1 3/4"L, Set of 4
|
|
|
When building an off road chassis, you can really uses these weld-on tabs to locate your seat belts, light mounts, etc. These tabs weld into place after you have decided where you want them! This Formed Tab has 20 degree breaks for better weld penetration
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Self Ejecting Stud
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
|
|
|
|
|
|
|
Universal Chassis Mounting Tab, Mild Steel, 1/2" Hole, Set of 4
|
|
|
When building an off road chassis, you can really uses these weld-on tabs to locate your seat belts, light mounts, etc. These tabs weld into place after you have decided where you want them!
These tabs are 2 1/4" long the long side, 1 1/2" tall, and have a 1/2" hole.
|
|
|
|
|
|
|
|
|
|
Corner Gusset, Set of 4
|
|
|
Most racing associations require gussets in the corners of tubing intersections. These gussets make that task relatively easy for the chassis builder. Pre-cut 1" diameter tubing with 45 degree ends makes for a clean and easy installation. Safer too!
|
|
|
|
|
|
|
|
|
|
Rubber Mounting Damper, 6 x 1mm Thread, EACH, 00-9259-7
|
|
|
Rubber Mounting Damper, 6 x 1mm Thread, EACH, 9259-7 is often used to eliminate vibration from vibrating electric fuel pumps, or external oil coolers. This uses a 10 x 1mm stud on either end, for easy mounting! These have more uses than you think! Sold per EACH.
|
|
|
|
|
|
|
|
|
|
Steering Hub Bracket, EACH
|
|
|
This is welded to the end of your steering shaft so you can bolt your steering wheel to it!
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Tab with Spring
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
|
|
|
|
|
|
DZUS Fastener, Spring Retainer
|
|
|
Dzus Fastener are THE Answer to attaching any panel when you are fabricating. Spring loaded self-ejecting Dzus Stud eliminates attaching hassles forever. Patented design affords a clean & neat appearance. Use for Tilt Front Ends, Aluminum Panels, & more.
|
|
|
|
